Biomaterials are in high demand due to the increasing geriatric population and a high prevalence of cardiovascular and orthopedic disorders. The combination of additive manufacturing (AM) and biomaterials is promising, especially towards patient-specific applications. With AM, unique and complex structures can be manufactured. Furthermore, the direct link to computer-aided design and digital scans allows for a direct replicable product. However, the appropriate selection of biomaterials and corresponding AM methods can be challenging but is a key factor for success. This article provides a concise material selection guide for the AM biomedical field. After providing a general description of biomaterial classes—biotolerant, bioinert, bioactive, and biodegradable—we give an overview of common ceramic, polymeric, and metallic biomaterials that can be produced by AM and review their biomedical and mechanical properties. As the field of load-bearing metallic implants experiences rapid growth, we dedicate a large portion of this review to this field and portray interesting future research directions. This article provides a general overview of the field, but it also provides possibilities for deepening the knowledge in specific aspects as it comprises comprehensive tables including materials, applications, AM techniques, and references.
5 November 2015 in International Journal of Production Research
Prototypes are important tools in the development and production of new products. In the engineering design literature, prototypes are mainly perceived as tools for validating and verifying aspects of a design in the late stages of the design process. However, several studies have found that prototypes are important in the earlier design stages as well, and it is currently unknown how prototypes contribute to add value within the overall value chains of a business system. Using a case-study approach, we investigate this topic seeking to answer the question of how prototypes and rapid prototyping add value in the various stages of the new product development process in the automotive industry. Based on our findings, we propose that the value of prototypes can be divided into the following three categories: the artefact, i.e. the prototype; the process, i.e. prototyping; or the experiment, i.e. the data generated from experimenting with the artefact. Finally, we argue that prototypes add value to both the production and knowledge value stream.
This paper demonstrates the unpredictability of outcomes that result from compounding variabilities when using generative design (GD) coupled with additive manufacturing (AM). AM technologies offer the greatest design freedom and hence are most able to leverage the full capability of generative design (GD) tools and thus maximize potential improvements, such as weight, waste and cost reduction, strength, and part consolidation. Implicit in all studies reported in the literature is the fundamental assumption that the use of GD, irrespective of user experience or approach followed, yields high-performing and/or comparable design outputs. This work demonstrates the contrary and shows that achieving high performance with GD tools requires careful consideration of study setup and initial conditions. It is further shown that, when coupled with the inherent variability of AM parts, the potential variation in the performance of the design output can be significant, with poorer designs achieving only a fraction of that of higher-performing designs. This investigation shows how AM by Material Extrusion (MEX), which is used to manufacture components with polylactic acid (PLA), varies through different design pathways, bridging MEX and GD. Through a practical study across nine independently generated designs, the breadth of performance—due to initial GD conditions and MEX part strength unpredictability—is shown to reach 592%. This result suggest that current GD tools, including their underlying workflows and algorithms, are not sufficiently understood for users to be able to generate consistent solutions for an input case. Further, the study purports that training and consideration on GD setup are necessary to apply GD toolsets to achieve high-performing designs, particularly when applied in the context of MEX.
The current limitations of design for additive manufacturing (DfAM) are the state of knowledge on materials and the effects of production parameters. As more engineering-grade polymers become available for fused filament fabrication (FFF), the designs and processes must be adapted to fully utilize the structural properties of such materials. By studying and comparing the production parameters of a material test specimen and a component, the effects of layer temperature on the strength, surface roughness, and dimensional accuracy of PA6-CF were found. As the cross-section increases in component manufacturing, maintaining the layer temperature becomes a major challenge. From the findings, the concept of thermal layer design (TLD) was introduced as a way of increasing strength via temperature in selected regions after presenting the effect of layer temperature. TLD proved to have a major effect on layer temperature and heat distribution. Depending on the investigated layer temperature, from 147 °C to 193 °C the UTS of PA6-CF increased from 42 MPa to 73 MPa. Implementing TLD in DfAM represents a big leap for designing high-performance polymer components.