Benedikt Uhe

Mr. Benedikt Uhe


Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
2 August 2020 in Production Engineering
Verified
Journal Article
Open access
PDF file
BUBenedikt Uhe
Benedikt Uhe
CKClara-Maria Kuball
Clara-Maria Kuball
MMMarion Merklein
Marion Merklein
GMGerson Meschut
Gerson Meschut
As a result of lightweight design, increased use is being made of high-strength steel and aluminium in car bodies. Self-piercing riveting is an established technique for joining these materials. The dissimilar properties of the two materials have led to a number of different rivet geometries in the past. Each rivet geometry fulfils the requirements of the materials within a limited range. In the present investigation, an improved rivet geometry is developed, which permits the reliable joining of two material combinations that could only be joined by two different rivet geometries up until now. Material combination 1 consists of high-strength steel on both sides, while material combination 2 comprises aluminium on the punch side and high-strength steel on the die side. The material flow and the stress and strain conditions prevailing during the joining process are analysed by means of numerical simulation. The rivet geometry is then improved step-by-step on the basis of this analysis. Finally, the improved rivet geometry is manufactured and the findings of the investigation are verified in experimental joining tests.

12 April 2021
Verified
Journal Article
Closed access
BUBenedikt Uhe
Benedikt Uhe
CKClara-Maria Kuball
Clara-Maria Kuball
MMMarion Merklein
Marion Merklein
GMGerson Meschut
Gerson Meschut
The use of high-strength steel and aluminium is rising due to the intensified efforts being made in lightweight design, and self-piercing riveting is becoming increasingly important. Conventional rivets for self-piercing riveting differ in their geometry, the material used, the condition of the material and the coating. To shorten the manufacturing process, the use of stainless steel with high strain hardening as the rivet material represents a promising approach. This allows the coating of the rivets to be omitted due to the corrosion resistance of the material and, since the strength of the stainless steel is achieved by cold forming, heat treatment is no longer required. In addition, it is possible to adjust the local strength within the rivet. Because of that, the authors have elaborated a concept for using high nitrogen steel 1.3815 as the rivet material. The present investigation focusses on the joint strength in order to evaluate the capability of rivets in high nitrogen steel by comparison to conventional rivets made of treatable steel. Due to certain challenges in the forming process of the high nitrogen steel rivets, deviations result from the targeted rivet geometry. Mainly these deviations cause a lower joint strength with these rivets, which is, however, adequate. All in all, the capability of the new rivet is proven by the results of this investigation.

11 July 2021
Verified
Book Chapter
Closed access
PDF file
BUBenedikt Uhe
Benedikt Uhe
CKClara-Maria Kuball
Clara-Maria Kuball
MMMarion Merklein
Marion Merklein
GMGerson Meschut
Gerson Meschut

Verified
Journal Article
Open access
PDF file
BUBenedikt Uhe
Benedikt Uhe
CKClara-Maria Kuball
Clara-Maria Kuball
Marion MerkleinMarion Merklein
Marion Merklein
Gerson MeschutGerson Meschut
Gerson Meschut
The sustainability of the manufacturing industry is of special importance to increase the protection of the environment. The production of fasteners like self-piercing rivets, however, is costly, time-consuming and energy-intensive. The heat treatment and the coating, which are mandatory in conventional self-piercing rivets to achieve adequate strength, ductility and corrosion resistance, are especially crucial in this respect. Within this paper, an approach for an increase in the sustainability in fastener production is presented. The use of alternative, high strain hardening stainless steels as rivet material enables a shortening of the process chain, because post treatment of the rivets after they are formed can be omitted. As the change in rivet material and processing causes some issues along the process chain, the focus of this paper is on the holistic evaluation of the challenges within the forming of high strain hardening steel and the impact of the changed rivet properties on the joining result.

29 August 2023
Verified
Book Chapter
Closed access
PDF file
BUBenedikt Uhe
Benedikt Uhe
CKClara-Maria Kuball
Clara-Maria Kuball
MMMarion Merklein
Marion Merklein
GMGerson Meschut
Gerson Meschut

31 January 2024 in Production Engineering
Verified
Journal Article
Open access
PDF file
BUBenedikt Uhe
Benedikt Uhe
CKClara-Maria Kuball
Clara-Maria Kuball
MMMarion Merklein
Marion Merklein
GMGerson Meschut
Gerson Meschut
Self-piercing riveting is an established joining technique for lightweight materials. To increase the sustainability of the rivet manufacturing process, the authors of the present paper have developed an approach for shortening the process chain by omitting the heat treatment and rivet coating. To do this, use is made of high nitrogen steel as the rivet material. Successful joining with these rivets has already been proven, and it has also been shown that a competitive joint strength can be achieved with these rivets. Up until now, no studies have been conducted of the corrosion behaviour of uncoated rivets in high nitrogen steel compared to conventional rivets made of heat-treatable steel with a coating of Almac® or zinc-nickel with topcoat, and the corrosion behaviour of joints manufactured with these rivets has also not been investigated. Furthermore, the suitability of rivets in high nitrogen steel for structures undergoing cathodic dip painting has not been evaluated to date. These are therefore the aims of the research work presented in this paper. Corrosion behaviour is tested by exposing rivets and joints to a salt spray atmosphere. Cross-cut tests are conducted in order to classify the adhesion of cathodic dip paint to the different rivet surfaces and materials. The results of the experimental test show that the cathodic dip paint has sufficient adhesion to the uncoated rivets in high nitrogen steel and that these rivets can therefore be used in the manufacture of car bodies. Due to the stainless properties of the high nitrogen steel, better corrosion resistance is seen by comparison to the commonly used coatings of Almac® and zinc-nickel with topcoat. A study of the corrosion behaviour of the joints shows that the rivet head diameter and rivet head position, in particular, are decisive for preventing crevice corrosion under the rivet head and contact corrosion within the joint.