The recently installed internal gas target at LHCb presents exceptional opportunities for an extensive physics program for heavy-ion, hadron, spin, and astroparticle physics. A storage cell placed in the LHC primary vacuum, an advanced Gas Feed System, the availability of multi-TeV proton and ion beams, and the recent upgrade of the LHCb detector make this project unique worldwide. In this paper, we outline the main components of the system, the physics prospects it offers, and the hardware challenges encountered during its implementation. The commissioning phase has yielded promising results, demonstrating that fixed-target collisions can occur concurrently with the collider mode without compromising efficient data acquisition and high-quality reconstruction of beam-gas and beam-beam interactions. Published by the American Physical Society 2024
High fracture toughness at cryogenic temperature and radiation hardness can be conflicting requirements for the resins for the impregnation of superconducting magnet coils. The fracture toughness of different epoxy-resin systems at room temperature (RT) and at 77 K was measured, and their toughness was compared with that determined for a polyurethane, polycarbonate (PC) and poly(methyl methacrylate) (PMMA). Among the epoxy resins tested in this study, the MY750 system has the highest 77 K fracture toughness of KIC = 4.6 MPa√m, which is comparable to the KIC of PMMA, which also exhibits linear elastic behaviour and unstable crack propagation. The polyurethane system tested has a much higher 77 K toughness than the epoxy resins, approaching the toughness of PC, which is known as one of the toughest polymer materials. CTD101K is the least performing in terms of fracture toughness. Despite this, it is used for the impregnation of large Nb3Sn coils for its good processing capabilities and relatively high radiation resistance. In this study, the fracture toughness of CTD101K was improved by adding the polyglycol flexibiliser Araldite DY040 as a fourth component. The different epoxy-resin systems were exposed to proton and gamma doses up to 38 MGy, and it was found that adding the DY040 flexibiliser to the CTD101K system did not significantly change the irradiation-induced ageing behaviour. The viscosity evolution of the uncured resin mix is not significantly changed when adding the DY040 flexibiliser, and at the processing temperature of 60 °C, the viscosity remains below 200 cP for more than 24 h. Therefore, the new resin referred to as POLAB Mix is now used for the impregnation of superconducting magnet coils.
The superconducting magnets of future particle accelerators will be exposed to high irradiation doses at cryogenic temperatures. To investigate the effect of irradiation temperature and atmosphere on the aging behavior, we have characterized the changes in thermomechanical properties of six epoxy resins for potential use in superconducting magnets after irradiation up to 20 MGy in ambient air, inert gas, and liquid helium. Based on the results obtained by Dynamic Mechanical Analysis (DMA), we discuss the effect of irradiation temperature and the presence of oxygen. The irradiation temperature can have a strong influence on the rates at which cross-linking and chain scission occur.
15 November 2023 in IEEE Transactions on Applied Superconductivity
Understanding the effect of radiation on the functional properties of epoxy resins is crucial for their application in future particle accelerators like the Future Circular Collider (FCC). We compare the irradiation induced aging rates of six epoxy resin systems that can be used for the vacuum impregnation of magnet coils. Aging is assessed based on Dynamical Mechanical Analysis (DMA), 3-point bending and outgassing tests. DMA storage and loss moduli evolutions reveal the effect of the competing influence of cross-linking and chain scission on the glass transition temperature ( Tg ). The same proton and gamma irradiation dose has a similar effect on the thermomechanical epoxy resin properties. Aging rates differ strongly for the different resins, and the fastest aging is observed for the MY750 resin system, which Tg decreases with a rate of about minus 9 °C/MGy.
Thin (<500 nm) single-stage coevaporated Cu(In,Ga)Se $_2$ absorber layers are treated with a KF postanneal in N $_2$ atmosphere. The conditions of the postanneal initial acceptor concentration and the temperature are varied. Solar cells are characterized with current–voltage and capacitance–voltage measurements. Efficiencies up to 12% with an open-circuit voltage ( $V_{oc}$ ) of >640 mV were achieved after the KF treatment. From SCAPS simulations and temperature dependent current voltage-measurements, it is concluded that the $V_{{\rm{oc}}}$ of these cells are limited by backcontact surface recombination and, thus, further improvements require passivation of the back contact.