Jose M. Abelleira-Pereira

Prof. Dr. Jose M. Abelleira-Pereira

orcid

Research Focus & Metrics

Academic Career Length

15Years (2012-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 March 2015 in Water Research
Verified
Journal Article
Closed access
Jose M. Abelleira-PereiraJose M. Abelleira-Pereira
Jose M. Abelleira-Pereira
SPSara I. Pérez-Elvira
Sara I. Pérez-Elvira
J. Sánchez-OnetoJ. Sánchez-Oneto
J. Sánchez-Oneto
RCRoberto de la Cruz
Roberto de la Cruz
Juan Ramón Portela MiguelezJuan Ramón Portela Miguelez
Juan Ramón Portela Miguelez
ENEnrique Nebot
Enrique Nebot

31 March 2012 in Environmental Science & Technology
Verified
Journal Article
Closed access
Jose M. Abelleira-PereiraJose M. Abelleira-Pereira
Jose M. Abelleira-Pereira
SPSara I. Pérez-Elvira
Sara I. Pérez-Elvira
Juan Ramón Portela MiguelezJuan Ramón Portela Miguelez
Juan Ramón Portela Miguelez
J. Sánchez-OnetoJ. Sánchez-Oneto
J. Sánchez-Oneto
ENEnrique Nebot
Enrique Nebot

4 June 2024 in International Journal of Hydrogen Energy
Verified
Journal Article
Open access
AMAntonio José Gil Mena
Antonio José Gil Mena
ABAbderraouf Bouakkaz
Abderraouf Bouakkaz
Jose M. Abelleira-PereiraJose M. Abelleira-Pereira
Jose M. Abelleira-Pereira
LGLuis Segovia Guerrero
Luis Segovia Guerrero
MRMaría de la Luz Martín Rodríguez
María de la Luz Martín Rodríguez

15 September 2023 in Journal of Material Cycles and Waste Management
Verified
Journal Article
Open access
PDF file
JMJ. J. Mascarell
J. J. Mascarell
FRF. J. Ruiz-Jorge
F. J. Ruiz-Jorge
Jose M. Abelleira-PereiraJose M. Abelleira-Pereira
Jose M. Abelleira-Pereira
Juan Ramón Portela MiguelezJuan Ramón Portela Miguelez
Juan Ramón Portela Miguelez
EOEnrique J. Martínez de la Ossa
Enrique J. Martínez de la Ossa
Hydrothermal Liquefaction (HTL) is a promising thermochemical treatment suitable for the valorization of a wide variety of organic wastes and wastewaters. Many research studies have demonstrated the suitability of HTL to produce bio-oil from biomass wastes, but few works have focused on the application of HTL to industrial wastes and wastewaters. The objective and novelty of this work are the study of HTL suitability over a specific selection of industrial residues that present notable drawbacks when treated by conventional waste management methods, including technical problems or high costs. Most of the wastes presented poor results from the technical or energetical point of view. However, liquid surfactant wastewaters were successfully treated by HTL at 300ºC and 100 bar in a 300 mL stirred batch reactor, producing a crude oil yield of around 16%, with a High Heating Value (HHV) of up to 30 MJ/kg. The composition and quality of the crude oils obtained have also been determined and compared against conventional biomass fuels. Graphical abstract

29 October 2024 in Applied Sciences
Verified
Journal Article
Open access
PDF file
JFJosé Manuel Vázquez Fernández
José Manuel Vázquez Fernández
Jose M. Abelleira-PereiraJose M. Abelleira-Pereira
Jose M. Abelleira-Pereira
M. Belen Garcia-JaranaM. Belen Garcia-Jarana
M. Belen Garcia-Jarana
LCLucio Cardozo-Filho
Lucio Cardozo-Filho
J. Sánchez-OnetoJ. Sánchez-Oneto
J. Sánchez-Oneto
Juan Ramón Portela MiguelezJuan Ramón Portela Miguelez
Juan Ramón Portela Miguelez
Epoxy resin composite matrices reinforced with carbon fibers are highly demanded by certain industries such as the aeronautics industry because of their exceptional mechanical properties. Unfortunately, the use of reinforcing carbon fibers makes these composite materials hard to recycle by conventional methods. Therefore, in this study, specific hydrothermal treatments have been employed to recover carbon fibers from the offcuts of composite parts from the aeronautics industry. The resin decomposition rates (DRs) achieved by different settings of the operating parameters, such as the use of alkaline catalysts (KOH, NaOH, or K2CO3), the application of mechanical stirring, the use of different reaction times, the solvent volume/composite mass ratio, the specific surface area (surface area/mass) of the composite pieces, and the operating temperature and pressure (subcritical or supercritical conditions), have been examined and assessed. Under the conditions that have been evaluated, resin decomposition rates nearly as high as 98% have been achieved, while the recycled fibers retained over 95% of their original tensile strength (TS).

27 December 2024 in Applied Sciences
Verified
Journal Article
Open access
PDF file
MIGUEL SUFFOMIGUEL SUFFO
MIGUEL SUFFO
Luis Romero GarciaLuis Romero Garcia
Luis Romero Garcia
Jose M. Abelleira-PereiraJose M. Abelleira-Pereira
Jose M. Abelleira-Pereira
PDPierpaolo D'Agostino
Pierpaolo D'Agostino
The leather industry is experiencing a significant rise in production, resulting in an increase in discarded materials–often classified as urban waste—that end up in landfills or are incinerated. Given the geographical proximity of the leather goods sector in Ubrique to the cork stopper manufacturing industry in El Puerto de Santa María/Jerez and to the viticulture sector in Jerez/Sanlúcar/Chiclana, it is essential to explore synergies that can address environmental challenges by contemplating a circular economy approach. This study focuses on the existing potential of repurposing discarded materials, such as reinforcements and linings, by meticulously recording, classifying, and characterizing them. The aim is to valorize these by-products in line with the circular economy principles set out by the European Union. Specifically, the research investigates the feasibility of using these materials as raw inputs, in combination with resins, to produce bottle stoppers for the high-end spirits industry. Findings indicate that a single company generates over six tons of textile waste per month, which equates to approximately EUR 25,000 annually in landfill disposal costs. By implementing a circular alternative that uses just 8.75% of these materials, an economic saving of around EUR 750 per year was reached. In addition, a low-cost vacuum molding method was tested for producing stoppers, yielding aesthetically pleasing and durable prototypes. The application of a materials circularity index enabled the identification of optimal remnants for reintroduction into the production cycle. This re-integration not only reduces the reliance on virgin plastic materials, but also has the potential to significantly reduce the overall environmental impact across interconnected sectors. Ultimately, this study highlights the viability of adopting circular economy practices within the leather goods sector to promote sustainability and economic efficiency.