The multi-functional nanomaterial constructed with more than one type of materials has gained a great attention due to its promising application. Here, a high white light photodetector prototype established with two-dimensional material (2D) and 2D nanocomposites has been fabricated. The 2D-2D nanocomposites were synthesized with SnSe nanoplate and graphene. The device shows a linear I-V characterization behavior in the dark and the resistance dramatically decreases under the white light. Furthermore, the photosensitivity of the device is as large as 1110% with a rapid response time, which is much higher than pristine SnSe nanostructure reported. The results shown here may provide a valuable guidance to design and fabricate the photodetector based on the 2D-2D nanocomposites even beyond the SnSe nanoplate-graphene nanocomposites.
As is well established, mastery to precise control of the layer number, stacking order of graphene, and the size of single-crystal monolayer graphene is very important for both fundamental interest and practical applications. In this report, millimeter-sized single-crystal monolayer graphene has been synthesized to multilayer graphene on Cu by chemical vapor deposition. The relationship of the growth process between monolayer graphene and multilayer graphene is investigated carefully. Besides the general multilayer graphene with Bernal stacking order, parts of multilayer graphene with non-Bernal stacking order were modulated under optimized growth conditions. The oxide nanoparticle on the Cu surface derived from annealing has been found to play the key role in nucleation. In addition, the hydrogen concentration impacts significantly on the layer number and shape of the graphene. Moreover, a possible mechanism was proposed to understand the growth process discussed above, which may provide an instruction to graphene growth on Cu by chemical vapor deposition.
CuPbSbS3 has excellent photoelectric properties, such as high element abundance and optical absorption coefficient, and a suitable band gap, which is a material with the potential for absorbing layers of high-quality thin film solar cells. In addition, CuPbSbS3 is a material with a three-dimensional structure, which can guide the carrier to transport in all directions, so its performance can be regulated in multiple dimensions. At present, the substrate structure is often used in efficient solar cells since this structure does not affect other functional layers when the absorption layer is subjected to harsh annealing conditions. However, there have been no reports of the substrate structure of CuPbSbS3 solar cells so far. Therefore, in this work, CuPbSbS3 films deposited on a stable substrate of molybdenum (Mo) were prepared with butyldithiocarbamic acid (BDCA) solution, and the preparation process of reaction mechanism was described in detail. It was found that the band gap of the CuPbSbS3 thin film was 2.0 eV and the absorption coefficient was up to 105 cm−1, which is expected to be applied to the top absorption layer material in laminated cells. Thus, we first built a Glass/Mo/CuPbSbS3/CdS/ZnO/ITO substrate structured solar cell. From this, a photoelectric conversion efficiency of 0.094% was achieved. This work provides a tentative exploration for the future development of substrate structured CuPbSbS3 solar cells.
Sb2S3 has emerged as a highly promising material for thin-film solar cells due to its low toxicity, excellent stability, and strong light absorption in the visible region. However, challenges such as the formation of the Sb2O3 secondary phase and S re-evaporation still exist during the high-temperature annealing of Sb2S3. To address these issues, this study introduces a strategy involving the pre-deposition of an ultrathin ZnO protective layer onto the Sb2S3 surface. The ZnO layer facilitates controlled oxygen passivation through a lattice-vacancy-mediated mass transfer mechanism, effectively suppressing the formation of Sb2O3 and minimizing Sb2S3 volatilization, while simultaneously forming a Zn-doping layer. The results show that Zn doping significantly enhances the energy level alignment at the back interface: the conduction band minimum (CBM) and valence band maximum (VBM) of the Sb2O3/Sb2S3 mixed layer are upshifted, and the Fermi level is downshifted, thereby promoting hole transport. Additionally, the carrier concentration increases, reducing the contact barrier with the carbon electrode. This modification enables the power conversion efficiency (PCE) of all-inorganic Sb2S3 solar cells with fluorine-doped tin oxide (FTO)/CdS/Sb2S3/PbS/Carbon/Ag structures to reach an impressive 7.00%, representing the most advanced performance level currently available and providing new guidance for the development of high-performance and low-cost all-inorganic Sb2S3 solar cells.