Flexible wearable strain sensors based on laser-induced graphene (LIG) have attracted significant interest due to their simple preparation process, three-dimensional porous structure, excellent electromechanical characteristics, and remarkable mechanical robustness. In this study, we demonstrated that LIG with various defects could be prepared on the surface of polyimide (PI) film, patterned in a single step by adjusting the scanning speed while maintaining a constant laser power of 12.4 W, and subjected to two repeated scans under ambient air conditions. The results indicated that LIG produced at a scanning speed of 70 mm/s exhibited an obvious stacked honeycomb micropore structure, and the flexible strain sensor fabricated with this material demonstrated stable resistance. The sensor exhibited high sensitivity within a low strain range of 0.4–8.0%, with the gauge factor (GF) reaching 107.8. The sensor demonstrated excellent stability and repeatable response at a strain of 2% after approximately 1000 repetitions. The flexible wearable LIG-based sensor with a serpentine bending structure could be used to detect various physiological signals, including pulse, finger bending, back of the hand relaxation and gripping, blinking eyes, smiling, drinking water, and speaking. The results of this study may serve as a reference for future applications in health monitoring, medical rehabilitation, and human–computer interactions.

The exceptional performance of graphene has driven the advancement of its preparation techniques and applications. Laser-induced graphene (LIG), as a novel graphene preparation technique, has been applied in various fields. Graphene periodic structures created by the LIG technique exhibit superhydrophobic characteristics and can be used for deicing and anti-icing applications, which are significantly influenced by the laser parameters. The laser surface treatment process was simulated by a finite element software analysis (COMSOL Multiphysics) to optimize the scanning parameter range, and the linear array surface structure was subsequently fabricated by the LIG technique. The generation of graphene was confirmed by Raman spectroscopy and energy-dispersive X-ray spectroscopy. The periodic linear array structure was observed by scanning electron microscopy (SEM) and confocal laser imaging (CLSM). In addition, CLSM testings, contact angle measurements, and delayed icing experiments were systematically performed to investigate the effect of scanning speed on surface hydrophobicity. The results show that high-quality and uniform graphene can be achieved using the laser scanning speed of 125 mm/s. The periodic linear array structures can obviously increase the contact angle and suppress delayed icing. Furthermore, these structures have the enhanced ability of the electric heating deicing, which can reach 100 °C and 240 °C within 15 s and within 60 s under the DC voltage power supply ranging from 3 to 7 V, respectively. These results indicate that the LIG technique can be developed to provide an efficient, economical, and convenient approach for preparing graphene and that the hydrophobic surface array structure based on LIG has considerable potential for deicing and anti-icing applications.

As a novel method to prepare graphene, the laser-induced graphene (LIG) technology has numerous outstanding properties and has been widely applied in various fields. Nevertheless, the challenge remains to easily and efficiently prepare multifunctional surfaces of graphene through laser microregulation and fine structure design. Here, we successfully fabricated a micron-structure gully graphene surface with hydrophobicity and electrothermal functionality under atmospheric conditions using a 10.6 μm CO₂ laser to directly write on the surface of a polyimide film (PI). The impact of the laser scanning speed on the surface morphology and chemical composition of the product was investigated by analyzing the SEM (scanning electron microscope) observations and Raman spectra, respectively. The mechanical stability of the surface was studied by analyzing the contact angle of water droplets on the surface after mechanical circulation and the delayed icing effect after repeated icing. The deicing and anti-icing performance of the surface were analyzed based on its resistance to surface icing and electric deicing time. According to the experimental results, we first observed a linear negative correlation between the generated structure linewidth and the laser scanning speed. Additionally, we successfully achieved one-step preparation of primitive continuous graphene structures with a superhydrophobic capability (151°). Furthermore, our findings indicate that micron-structured graphene surfaces exhibit excellent mechanical stability, effectively delay icing formation, and demonstrate efficient electric deicing effects. These results demonstrate the potential application of CO₂ laser-induced graphene technology in the field of surface preparation for deicing and anti-icing. This work offers a novel one-step approach for the fabrication of micron-structured heatable graphene surfaces with simultaneous superhydrophobicity, deicing, and anti-icing functionalities on polymer substrates.

There has been a significant shift in research focus in recent years toward laser-induced graphene (LIG), which is a high-performance material with immense potential for use in energy storage, ultrahydrophobic water applications, and electronic devices. In particular, LIG has demonstrated considerable potential in the field of high-precision human motion posture capture using flexible sensing materials. In this study, we investigated the surface morphology evolution and performance of LIG formed by varying the laser energy accumulation times. Further, to capture human motion posture, we evaluated the performance of highly accurate flexible wearable sensors based on LIG. The experimental results showed that the sensors prepared using LIG exhibited exceptional flexibility and mechanical performance when the laser energy accumulation was optimized three times. They exhibited remarkable attributes, such as high sensitivity (~41.4), a low detection limit (0.05%), a rapid time response (response time of ~150 ms; relaxation time of ~100 ms), and excellent response stability even after 2000 s at a strain of 1.0% or 8.0%. These findings unequivocally show that flexible wearable sensors based on LIG have significant potential for capturing human motion posture, wrist pulse rates, and eye blinking patterns. Moreover, the sensors can capture various physiological signals for pilots to provide real-time capturing.

The advancement in performance in the domain of flexible wearable strain sensors has become increasingly significant due to extensive research on laser-induced graphene (LIG). An innovative doping modification technique is required owing to the limited progress achieved by adjusting the laser parameters to enhance the LIG’s performance. By pre-treating with AgNO₃, we successfully manufactured LIG with a uniform dispersion of silver nanoparticles across its surface. The experimental results for the flexible strain sensor exhibit exceptional characteristics, including low resistance (183.4 Ω), high sensitivity (426.8), a response time of approximately 150 ms, and a relaxation time of about 200 ms. Moreover, this sensor demonstrates excellent stability under various tensile strains and remarkable repeatability during cyclic tests lasting up to 8000 s. Additionally, this technique yields favorable results in finger bending and hand back stretching experiments, holding significant reference value for preserving the inherent characteristics of LIG preparation in a single-step and in situ manner.

The exceptional performance of graphene has driven the advancement of its preparation technique and application. Laser-induced graphene (LIG), as a novel graphene preparation technique, has been applied in various fields. Graphene periodic structures created by LIG technique exhibit superhydrophobic characteristics and can be used for deicing and anti-icing applications, which are significantly influenced by the laser parameters. The laser surface treatment process was simulated by a finite element software analysis (COMSOL Multiphysics) to optimize the scanning parameter range, and the linear array surface structure were subsequently fabricated by the LIG technique. The generation of graphene was confirmed by Raman spectroscopy, and energy-dispersive X-ray spectroscopy. The periodic linear array structure were observed by Scanning electron microscopy (SEM) and confocal laser imaging (CLSM). In addition, CLSM testings, contact angle measurements, and delayed icing experiments were systematically performed to investigate the effect of scanning speed on surface hydrophobicity. The results show that the high quality and uniform graphene can be achieved using the laser scanning speed of 125 mm/s. The periodic linear array structures can obviously increase the contact angle and suppress delayed icing. Furthermore, these structures have the enhanced ability of the electric heating deicing, which can reach 100°C and 240°C within 15 s and within 60 s under the DC voltage power supply ranging from 3 to 7 V, respectively. These results indicate that the LIG technique can be developed to provide an efficient, economical, and convenient approach for preparing graphene and the hydrophobic surface array structure based on LIG has considerable potential for deicing and anti-icing applications.