Wide bandgap (WBG) semiconductor devices are developing rapidly due to their superior performance compared to traditional silicon-based devices. However, the packaging technology of traditional devices has limited the application of WBG semiconductor devices because of the challenges in electrical insulation. The complex environment of high blocking voltage, high frequency, and high temperature is the major reason for insulation failure of encapsulation structure. Therefore, in this article, an epoxy resin composite with nonlinear conductivity is proposed to be used as a coating to improve the electric field distribution of high-voltage high-power IGBT modules. First, an electrical field simulation model was built considering the thermal stress. It was found that the electric field in high temperature was improved compared with that in room temperature due to the temperature-dependent conductivity of silicone gel. Nevertheless, the risk of insulation failure still exists. After the application of nonlinear conductivity materials (NCMs) coating, the maximum electric field at the triple junctions and the ratio of electric field distortion in high field areas were significantly decreased. Further analysis showed that the optimization ratio of electric field increased with the increase of the blocking voltages or power losses in the IGBT chip. The results have demonstrated that the NCMs can reduce the maximum electric field in the IGBT encapsulation structure by 73% under the operating conditions of 120 W 10 kV. Partial discharge (PD) tests show that the partial discharge initial voltage (PDIV) of the substrates with NCM coating is increased by 33% compared with the normal encapsulation structure and the coating significantly inhibits the growth of electric trees. The presented results indicate that the NCMs have the potential to improve the insulation performance of high-voltage high-power IGBT modules.
12 December 2022 in IEEE Transactions on Dielectrics and Electrical Insulation
Trends toward high power density designs and emerging wide bandgap (WBG)-based semiconductors will lead to a severe temperature rise in power electronic modules. In this regard, the insulation performance of silicone gel used for power module packaging deteriorates at high temperatures and frequencies is a concern and has not been well studied. This study focuses on the electrical properties of silicone gel at high temperatures, including its dielectric properties, volume resistivity, and breakdown strength. A Cole-Cole model was used to describe the dielectric response process. In particular, the dielectric loss density under PWM voltage was calculated, and the temperature rise of the encapsulation structure caused by the dielectric loss was observed. It was found that the high-frequency dielectric constant at 200°C decreases by 24% compared to room temperature; when the temperature is raised to 180°C, the volume resistivity drops by three orders of magnitude, and the 50 Hz AC and 10 kHz unipolar square wave breakdown strength of silicone gel is reduced by 50% and 42% compared with those at room temperature. The dielectric loss under PWM voltage increases by four orders of magnitude as the temperature increases up to 200°C but does not lead to a significant temperature rise in the encapsulation structure.
IGBT power modules are usually used as circuit-breaking components in power systems, and are widely used in solid-state DC circuit breakers, hybrid DC circuit breakers, all-electric aircraft, high-speed railways, new energy vehicles, and power transmission systems. In these systems, IGBT power modules are usually faced with extremely harsh working conditions and there is a failure risk. Insulation degradation should be a cause for concern as a potential path of power module failure. In this paper, the discharge phenomena of the IGBT power module were observed based on Intensified Charge Coupled Devices (ICCD), and the triple junctions composed of copper–ceramic–silicone gel inside IGBT were found as the discharge points. Furthermore, the directed bonded copper (DBC) ceramic filled with silicone gel was used as a test sample to study the discharge failure process, including the partial discharge (PD), surface charges, and electric trees. The mechanism of discharge failure is discussed and analyzed. The insulation degradation process is accompanied by phenomena such as severe partial discharge and rapid electric tree growth. This research provides support for the analysis idea and guidance of the research method for the cause of power module failure.
30 May 2024 in IEEE Journal of Emerging and Selected Topics in Power Electronics
The development of high-voltage high power density electronic devices has brought forward new requirements for the insulation reliability of encapsulation. The growth of electrical trees at the triple junction of the silicone gel-copper-substrate is one of the most important causes of material degradation and even insulation failure. In this paper, the growth characteristics and degradation mechanism of electrical trees at the triple junction of power modules under high-frequency positive square wave voltage are studied. The results show that a higher frequency is conducive to the generation of bush trees. As the square wave rise time increases, the number of branches, length, and width of the electrical tree decreases. The denseness of the electrical tree decreases with an increase in the duty cycle of the square wave. In addition, electrical tree growth is modeled on the cavity initiation and propagation characteristics at the triple junction, where the injection and transport of the space charge play an important role. Electrical tree failure causes the deposition of disordered graphitic carbon in the vicinity of the copper electrode as well as the chemical degradation of the silicone gel, and it precipitates elemental Al from the Al2O3 substrate, which accelerates the insulation degradation.
30 April 2024 in IEEE Transactions on Dielectrics and Electrical Insulation
The insulating properties of silicone gel, which is widely used as the encapsulation of power electronic modules, directly determines their electrical insulation reliability, so the effects of applied voltage parameters in practical application scenarios should be investigated. In this paper, the effects of the frequency, rise time, and duty cycle of the positive repetitive square voltage on the initiation and growth characteristics of electrical trees in silicone gel are investigated by means of a pin-plate electrode structure to simulate spike-like defects in power electronic modules. The frequency mainly affected the growth characteristics of electrical trees after the initiation of electrical trees. The rise time has an effect on the tree inception voltage (TIV), and the duty cycle not only affect the growth characteristics of electrical trees but also the TIV. The related mechanisms are discussed and explained in detail. The findings are expected to provide a guidance for the design optimization and of reliability improvement of the encapsulation in high voltage power electronic modules.