Increasing demand to store intermittent renewable electricity from, e.g., photovoltaic and wind energy, has led to much research and development in large-scale stationary energy storage, for example, ZEBRA batteries (Na-NiCl2 solid electrolyte batteries). Replacing Ni with abundant and low-cost Zn makes the ZEBRA battery more cost-effective. However, few studies were performed on this next-generation ZEBRA (Na-ZnCl2) battery system, particularly on its AlCl3-NaCl-ZnCl2 secondary electrolyte. Its properties such as phase diagrams and vapor pressures are vital for the cell design and optimization. In our previous work, a simulation-assisted method for molten salt electrolyte selection has shown its successful application in development of molten salt batteries. The same method is used here to in-depth study the AlCl3-NaCl-ZnCl2 salt electrolyte in terms of its phase diagrams and vapor pressures via FactSageTM and thermo-analytical techniques (Differential Scanning Calorimetry (DSC) and OptiMeltTM), and their effects on battery performance such as operation safety and charging/discharging reaction mechanism. The DSC and OptiMelt results show that the experimental data such as melting temperatures and phase changes agree well with the simulated phase diagrams. Moreover, the FactSageTM simulation shows that the salt vapor pressure increases significantly with increasing temperature and molar fraction of AlCl3. The obtained phase diagrams and vapor pressures will be used in the secondary electrolyte selection, cell design and battery operation.
The utilization of the Solar Salt (60 wt%NaNO3/40 wt%KNO3) mixture as a Thermal Energy Storage (TES) medium is gaining importance due to its scalability and cost-effectiveness. However, the corrosion of metallic components presents a significant challenge. This study explores the intricate interplay between salt chemistry and its corrosivity, particularly at elevated temperatures exceeding the state-of-the-art bulk temperature 565 °C. The study manipulates salt decomposition by adjusting the oxygen partial pressure in the purge gas over Solar Salt and investigates the evolution of salt chemistry with and without the presence of steel. It analyzes the corrosion behavior of two types of stainless steel, AISI 316L and AISI 310, under different gas purging atmospheres. Furthermore, it employs a gold particle tracing technique to identify and monitor the formation and growth of the corrosion layer on the steel surface. The results reveal that nitrogen gas purging significantly enhances salt decomposition and its corrosivity over time. The presence of steel also influences salt decomposition depending on the purged gas atmosphere. In a nitrogen atmosphere, the presence of steel can increase the nitrite levels, while an air atmosphere results in an elevated concentration of oxide ions. In air, the AISI 310 alloy shows slightly better performance than AISI 316L. Both alloys experience substantial mass loss in the nitrogen-purged atmosphere. Interestingly, the presence of gold particles within the middle of the corrosion layer in the air purged atmosphere visually illustrates a counter diffusion involving various cations and anions across the corrosion layer.
Concentrated solar power (CSP) systems commonly use solar salt as a high temperature heat transfer and storage medium. This study examines the effect of oxygen (O 2 ) and nitrogen oxide (NO) gas concentrations on solar salt thermal stability and 310N stainless steel corrosion at 600°C up to 1224 h. The impact of the gas atmosphere (5–80 vol% O 2 , 400–600 ppm NO) on salt chemistry, including nitrate, nitrite, oxide, and chromate ions, was analyzed, and corrosion behavior was evaluated through weight change, corrosion rate, and microstructural analysis. The results show that introducing NO gas concentrations ≥ 400 ppm with at least 5 vol% O 2 stabilizes salt decomposition by controlling nitrite and oxide ion formation and promotes the development of a protective corrosion layer on the steel surface. Once this protective layer is formed, variations in oxygen concentration (5–80 vol%) in the presence of ≥ 400 ppm NO gas have a minimal long‐term effect on the corrosion behavior of stainless steel in solar salt. These findings underscore the importance of maintaining minimum O 2 and NO levels to optimize salt chemistry that effectively mitigates steel corrosion in solar salt systems.