Dinislam Iskanderovich Sadykov

Mr. Dinislam Iskanderovich Sadykov

orcid

Research Focus & Metrics

Academic Career Length

5Years (2022-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
28 December 2024 in Journal of Materials Research and Technology
Verified
Journal Article
Open access
AMAydar Mavlyutov
Aydar Mavlyutov
DKDemid Kirilenko
Demid Kirilenko
ALAlexander Levin
Alexander Levin
MMMaxim Yu. Murashkin
Maxim Yu. Murashkin
DSDinislam Iskanderovich Sadykov
Dinislam Iskanderovich Sadykov
Tatiana S. OrlovaTatiana S. Orlova
Tatiana S. Orlova

26 November 2022 in Materials
Verified
Journal Article
Open access
PDF file
Tatiana S. OrlovaTatiana S. Orlova
Tatiana S. Orlova
AMAydar Mavlyutov
Aydar Mavlyutov
MMMaxim Murashkin
Maxim Murashkin
NENariman Enikeev
Nariman Enikeev
AEAlexey Evstifeev
Alexey Evstifeev
Mikhail Yu GutkinMikhail Yu Gutkin
Mikhail Yu Gutkin
The influence of decreased temperature of tensile testing on annealing-induced hardening (AIH) and deformation-induced softening (DIS) effects has been studied in an ultrafine-grained (UFG) Al–Zr alloy produced by high-pressure torsion. We show that the UFG Al–Zr alloy demonstrates a DIS effect accompanied by a substantial increase in the elongation to failure δ (up to δ ≈ 30%) depending on the value of additional straining. Both the AIH and DIS effects weaken with a decrease in the tensile test temperature. The critical deformation temperatures were revealed at which the AIH and DIS effects are suppressed. The activation energy Q of plastic flow has been estimated for the UFG Al–Zr alloy in the as-processed, subsequently annealed and additionally strained states. It was shown that the annealing decreases the Q-value from ~80 kJ/mol to 23–28 kJ/mol, while the subsequent additional straining restores the initial Q-value. Alloying with Zr results in the expansion of the temperature range of the AIH effect manifestation to lower temperatures and results in the change in the Q-value in all of the studied states compared to the HPT-processed Al. The obtained Q-values and underlying flow mechanisms are discussed in correlation with specific microstructural features and in comparison to the UFG Al.

7 September 2023 in Metals
Verified
Journal Article
Open access
PDF file
Tatiana S. OrlovaTatiana S. Orlova
Tatiana S. Orlova
AMAydar Mavlyutov
Aydar Mavlyutov
DSDinislam Iskanderovich Sadykov
Dinislam Iskanderovich Sadykov
NENariman Enikeev
Nariman Enikeev
MMMaxim Murashkin
Maxim Murashkin
The influence of additional deformation heat treatments (DHTs), implemented by two regimes: (1) annealing and small additional deformation by high-pressure torsion (HPT) at room temperature (RT) and (2) HPT at elevated temperature to 10 turns and small additional HPT at RT, has been studied on the microstructure, mechanical properties and electrical conductivity of ultrafine-grained (UFG) Al-0.53Mg-0.27Zr (wt.%) alloy structured by HPT to 10 turns at RT. As is shown, both types of additional DHT lead to a substantial increase in plasticity (2–5 times) while maintaining high electrical conductivity (~53% IACS) and strength comprising 75–85% of the value in the pre-DHT state of the UFG alloy. The possible physical reasons for the revealed changes in the physical and mechanical properties are analyzed. Comparison of the strength and plasticity changes with the microstructure evolution after DHT of both types indicates that the increase in the density of introduced grain boundary dislocations is the most probable factor providing a tremendous increase in plasticity while maintaining a high level of strength in the UFG alloy under study. An outstanding combination of high strength (370 MPa), high elongation to failure (~15%) and significant electrical conductivity (~53% IACS) was achieved for the Al-Mg-Zr alloy. This combination of properties exceeds those obtained to date for this system, as well as for a number of other commercial conductor alloys based on the Al-Zr system.

5 May 2023 in Materials Science and Engineering: A
Verified
Journal Article
Closed access
Tatiana S. OrlovaTatiana S. Orlova
Tatiana S. Orlova
DSDinislam Iskanderovich Sadykov
Dinislam Iskanderovich Sadykov
DKDemid Kirilenko
Demid Kirilenko
ALA.I. Lihachev
A.I. Lihachev
ALAlexander Levin
Alexander Levin

1 April 2022 in Journal of Physics: Conference Series
Verified
Conference Paper
Open access
MMMaxim Murashkin
Maxim Murashkin
DSDinislam Iskanderovich Sadykov
Dinislam Iskanderovich Sadykov
AMAydar Mavlyutov
Aydar Mavlyutov
DMD K Magomedova
D K Magomedova
VKV U Kazykhanov
V U Kazykhanov
In this work, we demonstrate the possibility of producing a composite high strength and thermal resistant Al-based wire with ultrafine-grained (UFG) structure. Such composite wire consists of two aluminum alloys. Its clad is made of Al-1.17Mg-0.35Zr (wt.%) alloy, and the core is of Al-0.4Zr (wt.%). The specimens of Al alloys separately and as parts of a composite wire were subjected to thermomechanical treatment (TMT) that included annealing at 400°C, equal-channel angular pressing via “Conform” scheme (ECAP-C) and cold drawing (CD). The ratio between the core and clad materials in the composite wire was determined experimentally as well as calculated from the rule of mixtures (additivity). It has been shown that, an ultimate tensile strength over 360 MPa and a long-term operation temperature of 150°C can be achieved in a composite wire at a rational ratio between the chosen aluminum alloys with the UFG structures. Such combination of strength and thermal resistance is accompanied with an electrical conductivity of no less than 50% IACS in a composite wire.

2 December 2024 in Materials Letters
Verified
Journal Article
Closed access
DSDinislam Iskanderovich Sadykov
Dinislam Iskanderovich Sadykov
TOT.S. Orlova
T.S. Orlova
ALA.I. Lihachev
A.I. Lihachev
DKDemid Kirilenko
Demid Kirilenko