With the advantage of low-cost and small size, hall sensor has been exploited to detect motor position, and this strategy has attracted much attention. A challenge is that measurement model parameters vary with position and vary from motor to motor, because of the machining errors of permanent magnets. While, most existing methods use other auxiliary displacement sensors to calibrate model parameters off-line, which require a lot of preliminary work and lose adaptation when they are applied in industry. In this paper, an on-line simultaneous computation of model parameters and position method is proposed to measure position for permanent magnet synchronous linear motor. The measurement model with Fourier series is employed to approximate the mapping relationship between magnetic field strength and mover position. Based on the continuous variation characteristics of model parameters and position, a simultaneous computational algorithm is proposed to real-timely compute model parameters and position without other sensors. In experiments of one-way and reciprocating motion, magnetic field information is detected by a self-designed hall sensor array. Experimental results indicate the standard deviation of measurement error is less than 10μm with the comparison of reference optical encoder.
Grating interferometry is an environmentally stable displacement measurement technique that has significant potential for identifying the position of the wafer stage. A fast and precise algorithm is required for real-time calculation of six degrees-of-freedom (DOF) displacement using phase shifts of interference signals. Based on affine transformation, we analyze diffraction spot displacement and changes in the internal and external effective optical paths of the grating interferometer caused by the displacement of the wafer stage (DOWS); then, we establish a phase shift-DOWS model. To solve the DOWS in real time, we present a polynomial approximation algorithm that uses the frequency domain characteristics of nonlinearities to achieve model reduction. The presented algorithm is verified by experiment and ZEMAX simulation.
13 March 2012 in IEEE Transactions on Instrumentation and Measurement
Self-calibration technology is an important approach with the utilization of an artifact plate with mark positions that are not precisely known to calibrate the precision metrology system. In this paper, we study the self-calibration of xy precision metrology systems and present a holistic self-calibration algorithm based on the least squares method. The proposed strategy utilizes three traditional measurement views of an artifact plate on the xy metrology stage and provides relevant symmetry, transitivity, and redundancy. The misalignment errors of all measurement views, particularly errors of the translation view, are totally determined by detailed mathematical manipulations. Consequently, a least-squares-based robust estimation law is synthesized to calculate the stage error even under the existence of random measurement noise. Computer simulation validates that the proposed method can accurately realize the stage error when there is no random measurement noise. Furthermore, the calculation accuracy of the proposed scheme under various random measurement noises is studied, and the results verify that the proposed algorithm can effectively attenuate the effects of random measurement noise. The proposed strategy, in fact, provides a well-understood solution to the xy self-calibration problem for engineers in practical applications.
Grating interferometers that use large two-dimensional grating splice modules for performing wide-range measurements have significant advantages for identifying the position of the wafer stage. However, the manufacturing process of large two-dimensional grating splice modules is very difficult. In contrast to existing redundant designs in the grating line dimension, we propose a novel interferometric reading head with a redundant design for obtaining wide-range displacement measurements. This interferometric reading head uses a one-dimensional grating splice module, and it was observed to be compatible with two orthogonal gratings. We designed a grating interferometer system composed of four reading heads to achieve a wide range of measurements and verified it using ZEMAX simulation. By conducting experiments, we were able to verify the compatibility of the reading head with gratings possessing different grating line directions; the measurement noise was found to be less than 0.3 nm.
14 August 2017 in IEEE Transactions on Instrumentation and Measurement
Permanent magnet synchronous linear motor (PMSLM) and PM synchronous planar motor are important motion devices in the modern precision industry. Their inherent periodic magnetic fields are highly related to motor position. Correspondingly, the magnetic fields can be utilized to determine their own displacement and replace expensive sensors. However, the measurement result of this strategy seriously depends on magnetic field model (MFM) preciseness. To improve measurement accuracy, a novel MFM with Fourier series is proposed in this paper. First, a high-order theoretical model from theoretical derivation is developed. And the analyses show that even harmonics exist in the magnetic field of motor, which are not included in the theoretical model. This model deviation obviously affects measurement accuracy. Hence, the new MFM is reconstructed based on a high-order theoretical model. Comparative experiments with the three different MFMs are carried out to measure the displacement of the PMSLM. In the experiments, a linear hall sensors array containing eight sensors is self-developed to detect motor magnetic field. The root mean square of displacement measurement errors using a reconstruction model, a high-order theoretical model, and a fundamental model is 4.84, 8.42, and $758~\mu \text{m}$ , respectively. The experimental results validate that the measurement result of the proposed reconstruction MFM is better than the other two MFMs.
3 March 2017 in Measurement Science and Technology
Dual-frequency laser interferometer has been widely used in precision motion system as a displacement sensor, to achieve nanoscale positioning or synchronization accuracy. In a multi-channel laser interferometer synchronous measurement system, signal delays are different in the different channels, which will cause asynchronous measurement, and then lead to measurement error, synchronous measurement error (SME). Based on signal delay analysis of the measurement system, this paper presents a multi-channel SME framework for synchronous measurement, and establishes the model between SME and motion velocity. Further, a real-time compensation method for SME is proposed. This method has been verified in a self-developed laser interferometer signal processing board (SPB). The experiment result showed that, using this compensation method, at a motion velocity 0.89 m s −1 , the max SME between two measuring channels in the SPB is 1.1 nm. This method is more easily implemented and applied to engineering than the method of directly testing smaller signal delay.