Gabriela Mendes da Rocha Vaz

Mrs. Gabriela Mendes da Rocha Vaz


Research Focus & Metrics

Academic Career Length

4Years (2023-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
21 July 2023 in Biosensors
Verified
Journal Article
Open access
PDF file
GMGabriella Magarelli
Gabriella Magarelli
CBCínthia Caetano Bonatto
Cínthia Caetano Bonatto
GVGabriela Mendes da Rocha Vaz
Gabriela Mendes da Rocha Vaz
VLVictoria Baggi Mendonça Lauria
Victoria Baggi Mendonça Lauria
Luciano Paulino SilvaLuciano Paulino Silva
Luciano Paulino Silva
The global consumption of vegan foods is experiencing an expressive upward trend, underscoring the critical need for quality control measures based on nutritional and functional considerations. This study aimed to evaluate the functional quality of caviar and salmon analog food inks based on pulses combined with nano ingredients and produced in our laboratory (LNANO). The primary objective of this work was to determine the total antioxidant compounds contained in these samples using a voltammetric technique with a glassy carbon electrode. The samples underwent ethanolic extraction (70%) with 1 h of stirring. The voltammograms were acquired in a phosphate buffer electrolyte, pH 3.0 with Ag/AgCl (KCl 3 mol L−1) as the reference electrode and platinum wire as the auxiliary electrode. The voltammograms revealed prominent anodic current peaks at 0.76–0.78 V, which are attributed to isoflavones. Isoflavones, known secondary metabolites with substantial antioxidant potential commonly found in pulses, were identified. The total isoflavone concentrations obtained ranged from 31.5 to 64.3 mg Eq genistein 100 g−1. The results not only validated the efficacy of the electrochemical sensor for quantifying total antioxidant compounds in the samples but also demonstrated that the concentration of total isoflavones in caviar and salmon analogs fell within the expected limits.

1 March 2026 in Surfaces
Verified
Journal Article
Open access
PDF file
GVGabriela Mendes da Rocha Vaz
Gabriela Mendes da Rocha Vaz
JPJuliana Junqueira Pinelli
Juliana Junqueira Pinelli
CBCínthia Caetano Bonatto
Cínthia Caetano Bonatto
Luciano Paulino SilvaLuciano Paulino Silva
Luciano Paulino Silva
This study investigates the development and characterization of bioactive films incorporating silver nanoparticles (AgNPs) into biocompatible polymers, namely alginate and chitosan, fabricated using two methods, spin-coating and drop-casting, and aiming to enhance their antimicrobial properties. Dynamic light scattering (DLS) and electrophoretic mobility (EM) of the film precursor solutions revealed significant changes in the nanoparticles’ size and Zeta potential (ZP), reflecting the influence of polymer coatings. Alginate contributed to high electrostatic stability due to its negative charge, while chitosan facilitated specific interactions with negatively charged surfaces. Raman spectroscopy revealed that spin-coating conditions did not successfully result in film formation, highlighting the need for further optimization. Therefore, subsequent characterization studies were conducted only for the films formed by drop-casting. Topographical and nanomechanical assessments of these drop-cast films, using atomic force microscopy (AFM) and force spectroscopy, demonstrated that AgNPs reduced adhesion and elasticity in alginate films, while increasing rigidity and adhesion in chitosan-based films. Antimicrobial tests confirmed the efficacy of AgNPs in both precursor solutions and polymer films, with chitosan-based films that retained structural integrity, which makes them suitable for prolonged applications, while alginate films displayed rapid gelation upon hydration, potentially advantageous in short-term applications. The findings underscore the potential of these biopolymer-AgNP composites in creating antimicrobial materials for food packaging, wound dressings, and other biomedical applications. However, challenges related to film deposition methods, such as spin-coating, require further optimization to improve film formation and reproducibility.

20 October 2023 in Preprints.org
Verified
Preprint
Open access
PDF file
GVGabriela Mendes da Rocha Vaz
Gabriela Mendes da Rocha Vaz
Luciano Paulino SilvaLuciano Paulino Silva
Luciano Paulino Silva
In the bioprinting process, controlling the motion of bioprinters involves a computer-aided design (CAD) model, converting that model into g-code, and transmitting the motion commands to the bioprinters. The g-code file contains information about the motion of the axes and can be generated using various software. However, a challenge arises when using g-code between different bioprinters. Therefore, the objective of this study was to propose a reliable method for analyzing the differences in 3D bioprinting devices by parameterizing a crucial variable for extrusion bioprinting: the E-value. Four bioprinters from three different manufacturers were used to investigate the extrusion behavior when subjected to the same E-value.