Constance University Gnanasagaran

Ms. Constance University Gnanasagaran

orcid

Research Focus & Metrics

Academic Career Length

5Years (2022-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
7 October 2022 in Ceramics International
Verified
Journal Article
Open access
CGConstance University Gnanasagaran
Constance University Gnanasagaran
KRKarthikeyan Ramachandran
Karthikeyan Ramachandran
RSRamesh Singh
Ramesh Singh
SUSutharsini Ubenthiran
Sutharsini Ubenthiran
Nashrah Hani JamadonNashrah Hani Jamadon
Nashrah Hani Jamadon

21 February 2024 in Ceramics International
Verified
Journal Article
Open access
CGConstance University Gnanasagaran
Constance University Gnanasagaran
KRKarthikeyan Ramachandran
Karthikeyan Ramachandran
VKVishaal Harikrishna Kumar
Vishaal Harikrishna Kumar
VRVishwanathan Ramachandran
Vishwanathan Ramachandran
MRMurali Rangarajan
Murali Rangarajan

29 October 2023 in Heliyon
Verified
Journal Article
Open access
CGConstance University Gnanasagaran
Constance University Gnanasagaran
KRKarthikeyan Ramachandran
Karthikeyan Ramachandran
Nashrah Hani JamadonNashrah Hani Jamadon
Nashrah Hani Jamadon
VKVishaal Harikrishna Kumar
Vishaal Harikrishna Kumar
AMAndanastuti Muchtar
Andanastuti Muchtar
BABeenish Ayaz
Beenish Ayaz
This paper reports the microstructural characteristics and mechanical properties of yttria-stabilized zirconia prepared via fused deposition modelling and slip casting. X-Ray Diffraction peaks indicated that yttria-stabilized zirconia crystallized in tetragonal structure for both slip casted(SC) and fused deposition modelled(FDM) samples. Further, scanning electron microscopy of slip casted sample showcased closely packed structure with fine grains and an average grain size of ∼65 nm whilst fused deposition modelled samples showcased non-homogeneous pores with ∼20 nm grain size. Average relative density of slip casted samples was ∼99.4 % while that of fused deposition modelled sample exhibited ∼96.2 %. The Vickers Hardness of slip casted (∼15.26 ± 0.4 GPa) was ∼10 % higher than the fused deposition modelled samples (∼13.79 ± 0.3 GPa). Likewise, indentation fracture toughness of slip casted (5.78 ± 0.5 MPa m1/2) was 14 % higher than fused deposition modelled samples which could have been due to the change in grain size as well as porosity of the ceramics. Compressive strength of the fused deposition modelled samples was 32 % less than slip casted samples (∼510 ± 10 MPa) due to its non-homogenous pores which led to weakening van der Waals force of attraction.

24 April 2023 in Journal of Materials Research and Technology
Verified
Journal Article
Open access
KRKarthikeyan Ramachandran
Karthikeyan Ramachandran
CGConstance University Gnanasagaran
Constance University Gnanasagaran
APAshwath Pazhani
Ashwath Pazhani
VKVishaal Harikrishna Kumar
Vishaal Harikrishna Kumar
M. Anthony XaviorM. Anthony Xavior
M. Anthony Xavior
TAT. Arunkumar
T. Arunkumar

21 July 2023 in Proceedings of the Institution of Mechanical Engineers, Part H: Journal of Engineering in Medicine
Verified
Journal Article
Closed access
XAXinyi An
Xinyi An
PCPerk Lin Chong
Perk Lin Chong
IZIman Zohourkari
Iman Zohourkari
SRSandipan Roy
Sandipan Roy
AMAli Merdji
Ali Merdji
MYMohammad Hossein Yazdi
Mohammad Hossein Yazdi
The mechanical properties of tissue scaffolds are essential in providing stability for tissue repair and growth. Thus, the ability of scaffolds to withstand specific loads is crucial for scaffold design. Most research on scaffold pores focuses on grids with pore size and gradient structure, and many research models are based on scaffolding with vertically arranged holes. However, little attention is paid to the influence of the distribution of holes on the mechanical properties of the scaffold. To address this gap, this research investigates the effect of pore distribution on the mechanical properties of tissue scaffolds. The study involves four types of scaffold designs with regular and staggered pore arrangements and porosity ranging from 30% to 80%. Finite element analysis (FEA) was used to compare the mechanical properties of different scaffold designs, with von-Mises stress distribution maps generated for each scaffold. The results show that scaffolds with regular vertical holes exhibit a more uniform stress distribution and better mechanical performance than those with irregular holes. In contrast, the scaffold with a staggered arrangement of holes had a higher probability of stress concentration. The study emphasized the importance of balancing porosity and strength in scaffold design.

27 April 2023 in Advances in Materials and Processing Technologies
Verified
Journal Article
Open access
KRKarthikeyan Ramachandran
Karthikeyan Ramachandran
CGConstance University Gnanasagaran
Constance University Gnanasagaran
RSR Ram Subramani
R Ram Subramani
Vignesh BoopalanVignesh Boopalan
Vignesh Boopalan
ATArunkumar Thirugnanasambandam
Arunkumar Thirugnanasambandam
The fatigue behaviour of Al 6061 along with its ceramic nanoparticles reinforced cermets fabricated through ultrasonic-aided rheo-squeeze casting technique are evaluated. The fatigue behaviour was studied under ambient and elevated temperature (250°C) conditions, and the effect of notches was also examined under same stress conditions. Al 6061 indicated service life of ~1.15 million cycles at low stress value which dropped to 15,470 cycles with increase in stress magnitude. Al cermet (ALST) shwocased enhanced = fatigue life up to ~35% for hybrid cermet with highest service life of 1.71 million cycles due to load transfer mechanism. In elevated temperature condition, life of Al 6061 dropped by 37%, whereas the reinforced cermets remained higher with ALST revealing high service life cycles. Further, notch indicated drop in fatigue life of Al and its cermets with cermets prevailing better than Al. The elevated temperature notch represented the lowest fatigue life owing to stress concentration as well as the coefficient of thermal expansion mismatch.