The article presents experimental study results of the deformation state of composite cable space frame structures, including composite steel-concrete structures. Composite cable space frame structures are three-dimensional roof framing of long-span buildings. The designed constructions are a new type of roof framing structures and consist of typical composite steel-concrete modules connected with steel cable elements. The operation of composite cable space frame structures under load is characterised by geometric nonlinearity. The aim of the research is to study the deformation state and changing the geometric shape of experimental structures under the influence of external load. The technique of studying the deformation state of the composite cable space frame structures is based on the principles of digital photogrammetry. At the limit state the composite cable space frame structures change their regular shape. In this case, the central vertical points get the greatest vertical displacements, and the displacement value decreases closer to the supports. It is defined that the investigated construction has demonstrated combined action of all its components during the test, which indicates its effectiveness. The application of the photogrammetry method made possible to determine the moment of reaching the limit state of the composite cable space frame structures concretely.
The calculation of the steel unrestrained and partially restrained roof beams with initial imperfections main stages is discussed. Restraining can be done by structures attached to the steel beams, namely, profiled flooring and discrete joints. On the basis of the new approach to the internal forces analysis and the geometric properties specification, the purpose was to find and describe the differences in the beam work as the part of roofing, which distinguishes it from the work conditions of the free supported beam. The features of the beam operation with the joint flexural and torsion are singled out. The need to improve the existing theoretical model for present deficiencies elimination is indicated. The bearing capacity determining methods for the flexible elements stability exposed to bending and bending with torsion are compared. Their advantages and disadvantages are revealed. It is proposed to increase the material saving by applying calculations. At the end of the article, conclusions regarding the consideration of investigated factors are given.
The aim of the study is to identify main trends in the development of space grid structures. In order to reach the purpose it is necessary to conduct a review of the known structural concepts, nodal connections and specifics of the space grid structures and to make conclusions on feasibility improvement of the considered structural concepts that make it possible to develop new solutions without disadvantages residing in the analogues. Analysis of papers written by foreign and national scientists and devoted to theoretical, numerical and experimental studies of stress-strain state, influence of different factors on it and geometrical optimization and designing of space grid structures has been conducted in order to achieve the objectives. Space grid structures and, in particular, flat double-layer grid and most frequent nodes have been studied in the paper. The paper contains a short review of the history on development of space grid structures. It has been found that a rapid development of structural designs was caused by scientific and technical progress and, in particular, improvement of physical and mechanical properties of materials, development of calculation methods, application of software systems for simulating behavior of the structure under load, which significantly increased the calculation accuracy and reduced complexity of design. It has been also established that main parameters that have influence on effectiveness of a structural design are geometric dimensions of its modular elements, ratio of its depth to the span. The world experience on development of connection components has been studied in the paper. The paper presents general classification of nodal connections. Main advantages and disadvantages of existing space grid structures are highlighted and it allows to determine possible methods for their improvement. Theoretical research has permitted to establish that the main direction of spatial grid structures improvement consists in development of new node connection types. Several methods for node improvement have been proposed while taking into account the obtained results.
The stress-strain state of test specimens of the new combined system of support of a mine opening under imposed loads is studied. The test specimens are compound modular elements of the offered earlier combined system of support. Every single modular element is the regular quadrangular pyramid, consisting of a reinforced concrete slab and steel tube web members. The slab and web members are gathered in a complete element while concreting the slab. The tension sensor’s method of experimental research is applied to the test of specimens. The test of specimens is carried out under the load imposed with a hydraulic press. The load is set so that to imitate service conditions, including the most adverse. Design features of the offered support and test specimens are presented. Details of the support and its elements, sizes, production technology and assemblies are briefly described. The test methodology of specimens and the analysis of the results are presented. The load-carrying abilities of test specimens under the concentrated force and uniform load are obtained. Break down of slab and connection between the web members and the slab are the results of the test of the specimens under the concentrated force and the uniform load respectively.