To investigate the impact of tip clearance variation on the cavitation performance of a high-speed pump-jet propeller, Fluent software was employed for simulation calculations. The study utilized the RNG k-ε turbulence model and ZGB cavitation, conducting three-dimensional numerical simulations under both steady and transient conditions. A pump-jet propeller with a rated speed of 20,000 r/min was used to set three kinds of clearance for simulation, and the simulation proved to be reliable by comparison with the experiment. Initially, the analysis examined the effect of tip clearance on cavitation characteristics and cavitation volume under steady-state conditions, while also studying the distribution patterns of cavitation. Subsequently, the radial force and pressure pulsation of the jet propeller are analyzed by FFT processing, aiming at the influence of tip clearance on the structural strength of the pump-jet propeller. Under the design conditions, the smaller tip clearance shows better performance, while the larger tip clearance shows stronger anti-cavitation ability than the smaller clearance. In addition, the greater the tip clearance, the greater the radial force and pressure pulsation, which will adversely affect the pump-jet structure. The research results provide some references for further research on the effect of high-speed pump-jet propeller structures on performance.

Pump-jet propellers are currently the mainstream propulsion method for underwater vehicles, and cavitation is an important factor limiting the high speed and miniaturization of pump-jet propellers. In order to explore the cavitation performance of high-speed pump-jet propellers, based on the modified SST turbulence model and the Zwart cavitation model, a three-dimensional numerical simulation of unsteady internal cavitation flow was carried out by comparing the impeller with specific speed n_s = 1920 using FLUENT 2020R2 software. At the same time, the occurrence and development process of cavitation under 0.95 Q, 1.0 Q, and 1.05 Q conditions were analyzed (Q is the mass flow), the changes in gas volume fraction in the impeller channel were captured, the distribution characteristics of cavitation under different NPSH values were explored, and the change law of cavitation with time was determined. The results show that, when NPSH dropped to 95 m, the impeller cavitation first occurred under the 1.05 Q operating condition, and the impeller cavitation volume fraction was 0.0379525. When NPSH dropped to 85 m, the impeller cavitation occurred under the 1.0 Q operating condition, and the impeller cavitation volume fraction was 0.0185164. When NPSH dropped to 80 m, the impeller cavitation occurred under the condition of 0.95 Q, and the volume fraction of the impeller cavitation was 0.013541. The high-speed pump-jet propeller had better anti-cavitation ability with a small flow rate. The cavitation distribution law under the three operating conditions was similar; cavitation was first generated on the impeller inlet edge and near the shroud, and the vacuoles with large volumes were mostly concentrated on the impeller inlet side. As the NPSH gradually decreased, the entire flow channel was gradually occupied by vacuoles. As the flow decreased, the corresponding NPSH also decreased. When NPSH dropped to 50 m, the volume fraction of the impeller under all three operating conditions reached around 0.4. As the cavitation only occurred on the suction surface, the volume fraction of the cavitation on the suction surface exceeded 0.8, at which time the impeller had already undergone severe cavitation. Within a complete cycle, bubbles first appeared at the inlet edge of the impeller (measured near the shroud) and gradually spread toward the middle and rear of the impeller, ultimately covering the suction surface of the impeller. Under the design condition, the experimental results of the model pump were consistent with the numerical simulation results, and the error was only 2.68%, thus verifying the reliability of the numerical simulation. The research results provide a reference for the in-depth study of the cavitation performance of high-speed pump-jet propellers and provide a good theoretical basis and practical significance in the engineering field for the high-speed and miniaturization process of high-speed pump-jet propellers.

To investigate the transient characteristics of high-speed axial flow water-jet pumps during start-up and emergency acceleration as well as to analyze how different accelerations affect the performance of internal flow, the k–ω turbulence model of the SST model and Zwart cavitation model were used to perform unsteady simulation on an impeller rotating at a speed of 1850. The steady-state numerical simulation method was verified by the experimental data, the numerical calculation results were basically consistent with the experimental data, the margin of error was within 5%, and the numerical simulation method was reliable. The results show that there was an obvious transient effect in the process of variable speed, and the thrust reached a stable state later than the speed. The buffer times for start-up times of 1 s, 2 s, and 3 s were 0.0394 s, 0.0375 s, and 0.0282 s, respectively, and the buffer times for the acceleration times of 0.5 s, 1.0 s, and 1.5 s were 0.0330 s, 0.0273 s, and 0.0230 s, respectively. The greater the acceleration, the more serious the flow rate and thrust lag behind the speed, and the greater the impact thrust. Under the same acceleration, the buffer time required in the start-up process was 19.3~22.6% longer than that in the acceleration process. During the change in speed of the high-speed water-jet pump, the vortex core area of the suction surface (SS) first appeared on the side of the shroud at the inlet, increased with the increase in the rotational speed, and developed toward the middle of the impeller. However, after the flow was stabilized, the vortex core region gradually shrank and eventually disappeared. When the rotational speed reached 0.6 times the design speed, cavitation occurred at the leading edge (LE) of the blade, and the cavitation area increased with the increase in the rotational speed. When reaching the same speed, the greater the acceleration, the more serious the cavitation. Under the design speed, that is, 6000 r/min, the cavitation volume fraction of the 1 s start-up process was 7.32%, the 2 s start-up process was 5.84%, the 3 s start-up process was 5.32%, and the 0.5 s acceleration process was 6.86%. The cavitation volume fraction of the 1 s acceleration process was 5.04%, and that of the 1.5 s acceleration process was 4.23%. Under the same acceleration, the cavitation volume fraction of the start-up process was 6.7~25% larger than that of the acceleration process. Compared with the start-up process and acceleration process under the same acceleration, the accelerated process had a smaller region of vortex core, stronger anti-cavitation ability, and more stable flow than the start-up process. During the actual operation process of the water-jet pump, it is advisable to use smaller accelerations and segmented accelerations as much as possible until the design speed is reached. The research findings serve as a foundation for future investigations into the transient characteristics of high-speed water-jet pumps operating under variable speed conditions.