Microalgae contain a diversity of functional groups that can be used as environmental adsorbents. Spirulina platensis is a blue-green microalga that comprises protein-N, which is advantageous for use in nitrogen-containing biomass as adsorbents. This study aimed to enhance the adsorption properties of alginate hydrogels by employing Spirulina platensis. Spirulina platensis was immobilized on sodium alginate (S.P@Ca-SA) via crosslinking. The results of field-emission scanning electron microscopy, Fourier-transform infrared, and X-ray photoelectron spectroscopy analyses of the N-containing functional groups indicated that Spirulina platensis was successfully immobilized on the alginate matrix. We evaluated the effects of pH, concentration, and contact time on Pb(II) adsorption by S.P@Ca-SA. The results demonstrated that S.P@Ca-SA could effectively eliminate Pb(II) at pH 5, reaching equilibrium within 6 h, and the maximum Pb(II) sorption capacity of S.P@Ca-SA was 87.9 mg/g. Our results indicated that S.P@Ca-SA fits well with the pseudo-second-order and Freundlich models. Compared with Spirulina platensis and blank alginate beads, S.P@Ca-SA exhibited an enhanced Pb(II) adsorption efficiency. The correlation implies that the amino groups act as adsorption sites facilitating the elimination of Pb(II).
During the roasting of gold concentrate to improve gold recovery, arsenic is released into the air and valuable elements such as Fe, Cu, Zn, and Pb are converted into oxide minerals. In this research, we evaluated the release of As and the loss of valuable metals during the acid baking and hot water leaching processes used for gold concentrate. The acid bake tests were conducted for gold concentrate using an electric furnace by applying various concentrations of H2SO4 solution under different baking times. The water leaching process was enacted using 70 °C water for the baked samples. Chemical and mineral compositions of the raw and treated samples were analyzed using AAS and XRD, respectively. The results show that soluble metal sulfates, such as rhomboclase and mikasite, were formed in the baked samples, and that the leaching of valuable metals (Fe, Cu, Zn, and Pb) was accelerated during the hot water leaching procedure. During acid baking, arsenic was partially removed by volatilization, and the rest of the arsenic-containing minerals were converted to soluble minerals. The soluble arsenic-containing mineral resulted in a dissolution that was 60 times higher than in the roasted sample. The maximum gold grade of solid residues increased up to 33% through the acid baking–water leaching process. It was confirmed that acid baking with H2SO4 prevented As release into the air, as well as the recovery of valuable metals through hot water leaching, such as Fe, Cu, Zn, and Pb, which were formerly discarded in the tailings.
This study investigates bubble size measurements, bubble characteristics, and the relationship between key operating variables and gas dispersion properties in column flotation. As the frother concentration increased to 120 ppm, the bubble size distribution (BSD) transformed from bimodal to unimodal and achieved a minimum bubble size of 0.62 mm. The critical coalescence concentration (CCC) was identified as 120 ppm. Gas velocity and wash water velocity significantly influenced bubble size, with gas holdup peaking at 27% at 1.08 cm/s a gas velocity. The bubble-rising velocity increased as the bubble size increased, indicating that the bubble size and bubble-rising velocity were proportional. The bubble surface area flux decreased linearly with increasing bubble size and was significantly affected by the gas velocity. A strong correlation (R2 = 0.86) between measured and calculated bubble sizes was achieved, with an average size of 0.64 mm and an estimation error of ±13%. The study demonstrated that bubble size and distribution could be effectively controlled under specific operational conditions (Jg = 0.65–1.3 cm/s, JW = 0.13–0.52 cm/s, frother = 30–120 ppm). These findings highlight the importance of optimizing key variables to enhance column stability, regime maintenance, and flotation performance.
Printed circuit boards (PCBs) are difficult to recycle because of the layered structure of non-metal (i.e., epoxy resin, glass fiber) and copper. In this work, we conducted a systematic investigation to effectively recover copper from PCB. A thermal treatment was employed for improving the crushing performance of PCB and conducted by varying the temperature and the gas. Then, the mechanical strength, degree of liberation (DL), and copper separation efficiency of the heat-treated and untreated PCBs were investigated. After heat treatment under a 300 °C air atmosphere, the mechanical strength of PCB decreased from 386.36 to 24.26 MPa, and copper liberation improved from 9.3% to 100% in the size range of a coarser size fraction (>1400 μm). Accordingly, when electrostatic separations were performed under these conditions, a high-Cu-grade concentrate and high recovery could be obtained. The results show that the change in the physical properties of the PCBs leads to an improvement in the DL following thermal decomposition at 300 °C in air. Our study elucidates the physical properties of PCBs and the DL under various heat treatment conditions. Furthermore, it shows that the heat treatment condition of 300 °C in air is ideal for recovering copper from the PCB.
Automobile-shredder-residue (ASR) recycling techniques have been widely applied for improving the total recycling rate of end-of-life vehicles. In this study, to obtain useful information for predicting or improving ASR-separation efficiency, trajectory analyses of conductors (copper) and non-conductors (glass) were performed using a lab-scale induction electrostatic separator. The copper-wire trajectories obtained showed a good agreement depending significantly on the electric field strength and particle size. The observed copper-wire trajectories showed consistent congruity with the coarse-particles simulation (0.5 and 0.25 mm). The observed fine-particles (0.06 mm) trajectory was deflected toward the (−) attractive electrode, owing to the charge density effects due to the particle characteristics and relative humidity. This results in superior separation performance because more copper enters the conductor products bin. The actual dielectric-glass trajectory was deflected toward the (−) attractive electrode, thus showing characteristics similar to conductive-particle characteristics. Through analyses conducted using a stereoscopic microscope, scanning electron microscope, and energy dispersive spectroscope, we found heterogeneous materials (fine ferrous particles and conductive organics) on the glass surface. This demonstrates the separation-efficiency decrease for non-ferrous metals during electrostatic separation in the recycling of ASR. Future work should include a pretreatment process for eliminating impurities from the glass and advanced trajectory-simulation processes.