Steel tube confined concrete (STCC) stub columns have great strength and facilitate construction. In this study, the axial compressive strength of an aluminum alloy tube confined concrete column with (ATCC-CHS) and without (ATCC) a circular hollow section was tested in laboratory experiments. The influence of concrete strength, diameter–thickness ratio and the hollow rate on the failure mode, ultimate compressive strength, strain, stiffness, constraint effects and ductility was quantified. The experiments showed that local buckling failure could be effectively delayed when the outer aluminum tube did not directly bear axial load. Columns without a circular hollow section had bearing capacities approximately 20% higher than those with a circular hollow section, though their ductility was poorer. The ultimate strength tended to increase with decreases in the hollow rate and diameter–thickness ratio. It tended to increase with increasing concrete strength, though stronger concrete also reduced ductility. The bearing capacities of the columns were calculated according to several proposed formulas and compared with the experimental results, and the proposed Teng and Attard’s formula appeared to be satisfactory.
The steel tube-reinforced concrete (STRC) shear wall plays an important role in the seismic design of high-rise building structures. Due to the synergistic collaboration between steel tubes and concrete, they effectively enhance the ductility and energy dissipation capacity of conventional shear walls. To identify vulnerable areas prone to brittle failure and optimize the design, it is essential to develop a rapid method for identifying the failure mode of STRC shear walls. In this study, a fast identification method of STCR shear wall failure modes based on a Blending fusion model with Generative Adversarial Network (GAN) augmented data is proposed. The GAN is employed to address the issue of inadequate experimental data by generating new samples. This method combines classification boosting (Catboost), Random Forest (RF), K-Nearest Neighbors (KNN), and Least Absolute Shrinkage and Selection Operator (LASSO) to establish the Blending-CRKL fusion model to improve the prediction accuracy of the failure mode of STRC shear walls. The results reveal a significant improvement in the prediction performance of KNN, Backpropagation Neural Network (BPNN), RF, Light Gradient Boosting Machine (LightGBM), Catboost, and Blending-CRKL models after augmenting the training set with GAN. On average, the accuracy increased by 13%, precision increased by 81%, recall increased by 48%, and F1 score increased by 67%. The proposed Blending-CRKL fusion model outperforms the tested KNN, BPNN, RF, LightGBM, and Catboost models, achieving an accuracy rate of 97% in predicting the failure mode of STRC shear walls. Additionally, the stability and robustness of the Blending-CRKL model were validated, while the important features and value ranges of different failure modes were analyzed. This study provides a reference for the rapid identification of the failure mode of STRC shear walls.
To reduce the computational cost associated with traditional moving heat source methods, a segmented approach is proposed for simulating the welding process of T-joints in large-scale infrastructure steel modules. Firstly, the hole-drilling method was employed to measure the welding residual stresses in a 2400 mm T-joint. Subsequently, a three-dimensional finite element model was established in ABAQUS, and a user-defined subroutine for the segmented moving heat source was developed in Fortran to calculate the welding residual stresses. The numerical simulation results were compared with experimental data, showing high consistency and further validating the accuracy of the finite element model. Furthermore, the distribution patterns of residual stresses along the thickness direction and the effects of different welding sequences on temperature, stress, and deformation were investigated to optimize the welding sequence. The results indicated that the residual stresses along the weld seam exhibited a compressive–tensile–compressive distribution, with the maximum tensile stress reaching approximately 347 MPa. Additionally, the simulation results demonstrated that the double-ellipsoidal heat source method was computationally intensive and failed to provide accurate results for long weld seams, whereas the segmented moving heat source approach reduced the computation time to only 38 h. Moreover, different welding sequences had a significant impact on residual stresses and deformation. Through comprehensive analysis, it was found that Case 1 (sequential welding in the forward direction) achieved the best performance in minimizing welding residual stresses and deformation.