This paper presents an analysis of the fracture accident of a cylindrical roller bearing cage used in a charging pump in a nuclear power plant. The causes and mechanisms of bearing cage breakage were investigated by material failure analysis and simulation calculations. Macroscopic observation results confirmed that the cage fracture occurred at the stress concentration position. The microfracture morphology of the cage obtained from scanning electron microscopy showed a fatigue feature. The analysis of residual stress indicated large residual stress perpendicular to the fracture surface. The finite element calculation showed that when the bearing was moving in and out of the working area during operation, large working stress appeared at the stress concentration position. Working stress and residual stress acted together, approaching the fatigue limit of materials, and finally led to the cage fatigue fracture. The stress of the other two structural cages of the same type of bearing was also calculated, and no such large stress concentration was identified; thus, one plastic cage was temporarily used.
With the increased power density of internal combustion engines (ICE) and growing demands for lightweight design, the connecting rod big-end bearings are subjected to significant alternating loads. Consequently, the interference–fit interfaces become susceptible to fretting damage, which can markedly shorten engine service life and impair reliability. In the present study, the effects of the big end manufacturing process, bolt preload, and bearing bush interference fit are considered to develop a coupled lubrication–dynamic model of the connecting rod big-end bearing. This model investigates the fretting damage issue in the bearing bush of a marine diesel engine’s connecting rod big end. The results indicate that the relatively low stiffness of the big end is the primary cause of bearing bush fretting damage. Interference fit markedly affects fretting wear on the bush back, whereas the influence of bolt preload is secondary; nevertheless, a decrease in either parameter enlarges the fretting distance. Based on these findings, an optimized design scheme is proposed.
Describes the internal audit function in a joint venture company. Auditing joint ventures is a fascinating topic, particularly when it involves the nuclear power industry and partnership between China and a foreign collaborator. The internal audit function was established right at the outset and has a high profile in the corporate governance structure. Its position is safeguarded in an audit charter, and a whole range of techniques and approaches guarantees a comprehensive service based on risk assessment. A combination of specific audits, special studies, internal control verifications, pre‐award audits and irregularities reports demonstrate that the internal audit arrangements are at the cutting edge of best practice.
A circulating water pump is a key equipment of cooling systems in nuclear power plants. Several anchor bolts were broken at the inlet rings of the same type of pumps. The bolts were turned by a special material for seawater corrosion protection. There were obvious turning tool marks at the root of the thread, which was considered as the source of the crack. The fatigue crack extended to the depth of the bolt, causing obvious radiation stripes on the fracture surface, which was a typical fatigue fracture. Obvious overtightening characteristics were found at the head of the broken bolt. Fracture and energy spectrum analysis showed that the bolt was not corroded. The axial vibration of the pump was measured. The static tensile stress along the bolt axis caused by the preload, the axial tensile stress caused by the axial vibration, and the torsional stress were calculated, respectively. According to the fatigue strength theory, the composite safety factor of the bolt fatigue strength was 1.37 when overtightening at 1.2 times the design torque, which was less than the allowable safety factor of 1.5-1.8, so the bolt was not safe, which further verified the conclusion of fracture analysis. The reason for the low safety factor was caused by the overtightening force. The improvement method was to control the bolt preload or increasing the bolt diameter.
1 January 2017 in The Proceedings of Conference of Kyushu Branch
Fatigue strength and failure mechanisms of welded joints in very high cycle fatigue (VHCF) regime are presented based on our recent experimental studies. We compare the fatigue strength between fusion welding, laser-hybrid welding, and friction stir welding so as to optimize welding parameters for fatigue life improvement. In addition, the effects of welding defects, microstructural heterogeneities and the second phase inclusions or particles on fatigue crack initiation process are discussed. The results indicate that VHCF behavior of welded joints showed strong sensitivity to microstructural and mechanical heterogeneities.