Yi Jiang

Dr. Yi Jiang


Research Focus & Metrics

Academic Career Length

5Years (2022-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
16 September 2022 in Sensors
Verified
Journal Article
Open access
PDF file
YYYuan Yang
Yuan Yang
PWPing Wang
Ping Wang
TSTian-Lang Song
Tian-Lang Song
YJYi Jiang
Yi Jiang
WZWen-Tao Zhou
Wen-Tao Zhou
WXWei-Lei Xu
Wei-Lei Xu
A method based on the high-frequency ultrasonic guided waves (UGWs) of a piezoelectric sensor array is proposed to monitor the depth of transverse cracks in rail bottoms. Selecting high-frequency UGWs with a center frequency of 350 kHz can enable the monitoring of cracks with a depth of 3.3 mm. The method of arranging piezoelectric sensor arrays on the upper surface and side of the rail bottom is simulated and analyzed, which allows the comprehensive monitoring of transverse cracks at different depths in the rail bottom. The multi-value domain features of the UGW signals are further extracted, and a back propagation neural network (BPNN) is used to establish the evaluation model of the transverse crack depth for the rail bottom. The optimal evaluation model of multi-path combination is reconstructed with the minimum value of the root mean square error (RMSE) as the evaluation standard. After testing and comparison, it was found that each metric of the reconstructed model is significantly better than each individual path; the RMSE is reduced to 0.3762; the coefficient of determination R2 reached 0.9932; the number of individual evaluation values with a relative error of less than 10% and 5% accounted for 100% and 87.50% of the total number of evaluations, respectively.

17 September 2023 in Ultrasonics
Verified
Journal Article
Closed access
YYYuan Yang
Yuan Yang
PWPing Wang
Ping Wang
YJYinliang Jia
Yinliang Jia
LJLixuan Jing
Lixuan Jing
YSYu Shi
Yu Shi
XLXin Li
Xin Li

18 December 2024 in Sensors
Verified
Journal Article
Open access
PDF file
LHLei Han
Lei Han
YJYi Jiang
Yi Jiang
MYMing Yuan
Ming Yuan
The design and study of pulsed eddy current sensors for detecting surface defects in small-diameter rods are highly significant. Accurate detection and identification of surface defects in small-diameter rods may be attained by the ongoing optimization of sensor design and enhancement of detection technologies. This article presents the construction of a non-coaxial differential eddy current sensor (Tx-Rx sensor) and examines the detection of surface defects in a small diameter bar. A COMSOL 3D model is developed to examine the variations in eddy current distribution and defect signal characteristics between the plate and rod components. The position of the excitation coil on the bar and the eddy current disruption around the defect are examined. Additionally, a Tx-Rx sensor has been developed and enhanced concerning coil dimensions, coil separation, and elevation height. An experimental system is established to detect bar structures with surface defects of varying depths, and a model correlating differential signal attenuation with defect depth is proposed, achieving a quantitative relative error of less than 5%, thereby offering a reference for the quantitative detection of bar surface defects.

1 March 2023 in Russian Journal of Nondestructive Testing
Verified
Journal Article
Closed access
PDF file
YJYi Jiang
Yi Jiang
LHLei Han
Lei Han
ZWZhaoxin Wang
Zhaoxin Wang
HWHaitao Wang
Haitao Wang
ZSZhongwen Shen
Zhongwen Shen
Selective laser melting (SLM) is an important method of additive manufacturing (AM). However, due to the large temperature gradient, defects such as pores and inclusions are easily visible during the printing process, affecting the forming quality and internal mechanical properties of the parts. This paper proposes a lase-SAFT detection method based on longitudinal wave to detect internal defects in additive parts. The mathematical model of the laser-SAFT algorithm is developed, and simulation research on the quantitative detection technique of AM 316L steel’s internal defects is conducted. A de-artifact approach based on wave mode and flight duration is presented to increase the accuracy of imaging results. The detecting impact of double-defect within the AM 316L steel is also modelled. Finally, the SAFT imaging of various locations and sizes of defects in the AM 316L steel, as well as the SAFT imaging detection of double-defect, are accomplished.

1 November 2023 in Russian Journal of Nondestructive Testing
Verified
Journal Article
Closed access
PDF file
YJYi Jiang
Yi Jiang
RWRongyao Wang
Rongyao Wang
LHLei Han
Lei Han
ZWZhaoxin Wang
Zhaoxin Wang
Fatigue oblique cracks are the most common type of surface damage on steel rails, although they are microscopic and difficult to detect. Rail crack can occur as the crack length increases. This paper presents a method for detecting laser ultrasonic surface waves that is fully non-contact and unaffected by complicated surfaces. To solve the difficulties of low photoacoustic conversion efficiency and poor imaging impact of laser ultrasound, a solution combining particle swarm optimization (PSO) based VMD parameter optimization algorithm with Sobel image edge processing algorithm is presented. This enhances the signal-to-noise ratio (SNR) and image accuracy while also allowing for the quantitative identification of oblique fissures of varying lengths. The highest quantitative error is less than 4%, and the smallest quantitative error is 1.4%.

22 May 2023 in Russian Journal of Nondestructive Testing
Verified
Journal Article
Closed access
PDF file
YJYi Jiang
Yi Jiang
LHLei Han
Lei Han
RWRongyao Wang
Rongyao Wang
JCJingting Cheng
Jingting Cheng
Manual visual inspection of the action rod of a rail switch machine is wasteful and incapable of detecting interior faults. As a result, this work describes an image quantitative detection approach for internal action rod flaws based on pulse reflection ultrasonic detection technology. First, the sound field properties are studied using simulation, and the best probe parameters are chosen. The rectangular and round rods’ signals are then acquired using circumferential scanning testing, and image reconstruction of the scanned data is performed based on the energy characteristics. Finally, the 8-neighborhood connection technique is developed to quantitatively assess the interior oblique fractures of the rectangular rod, with a relative length inaccuracy of less than 2.2%. In addition, the energy superposition method and polar image transformation are utilized to quantitatively examine the round rod’s interior hole flaws. The observed internal hole flaws have a relative error of diameter detection of less than 5% and a relative error of depth location in the radial direction of less than 3%.