Yaroslav Ignatenko

Mr. Yaroslav Ignatenko

orcid

Research Focus & Metrics

Academic Career Length

10Years (2017-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
19 October 2023 in Fluids
Verified
Journal Article
Open access
PDF file
AGAndrey Gavrilov
Andrey Gavrilov
YIYaroslav Ignatenko
Yaroslav Ignatenko
A fully developed turbulent flow in a concentric annulus, Re =10,000, ri/ro=0.5, with an inner rotating cylinder in the velocity range N=Uω/Ub=0÷4, is studied via a large-eddy simulation. Also, for comparison, simulations by steady-state, unstatiounary RANS k-ω SST (URANS), and Elliptic Blending Model (EBM) were made. The main focus of this study is on the effect of high rotation on the mean flow, turbulence statistics, and vortex structure. Distribution of the tangential velocity and the Reynolds stress tensor change their behaviour at N>0.5∼1. With rotation increases, the production of tangential fluctuation becomes dominant over axial ones and the position of turbulent kinetic energy maximum shifts towards the wall into the buffer zone. URANS and EBM approaches show good agreement with LES in mean flow, turbulent statistics, and integral parameters. The difference in pressure loss prediction between LES and URANS does not exceed 20%, but the average difference is about 11%. The EBM approach underestimates pressure losses up to 9% and on average not more than 5%. Vortex structures are described well by URANS.

7 November 2024 in European Journal of Mechanics - B/Fluids
Verified
Journal Article
Closed access
YIYaroslav Ignatenko
Yaroslav Ignatenko
AGAndrey Gavrilov
Andrey Gavrilov
OBOleg B. Bocharov
Oleg B. Bocharov
RARoger Aragall
Roger Aragall

25 October 2017 in EPJ Web of Conferences
Verified
Journal Article
Open access
PDF file
YIYaroslav Ignatenko
Yaroslav Ignatenko
OBOleg Bocharov
Oleg Bocharov
RMRoland May
Roland May
Parametrical study of perfect steady rolling and steady state freely motion of spherical particle on the wall in shear flow of non-Newtonian fluid was carried out. In the case of perfect rolling the jumps of forces acting on a sphere in the moment of changing particle velocity from zero to positive were observed. Non-Newtonian properties of fluid lead to decreasing of drag force coefficient for low particle's velocity and to opposite effect for high velocity relative to Newtonian fluid. There is no such significant effect for a lift force coefficient. Steady state particle's velocity (Fd(Vpss)=0) increases for non-Newtonian fluid for both considered types of motion. Steady state particle's velocity and lift force coefficient are lower for the case of freely particle motion. Steady state rotational velocity decreases for non-Newtonian fluid.

14 January 2019 in EPJ Web of Conferences
Verified
Journal Article
Open access
YIYaroslav Ignatenko
Yaroslav Ignatenko
AGAndrey Gavrilov
Andrey Gavrilov
OBOleg Bocharov
Oleg Bocharov
RMRoland May
Roland May
The current study is devoted to simulating cuttings transport by drilling fluid through a horizontal section of borehole with an annular cross section. Drill pipe rotates in fixed eccentric position. Steady-state flow is considered. Cuttings are rigid spheres with equal diameters. The carrying fluid is drilling mud with Herschel-Bulkley rheology. Suspension rheology depends on local shear rate and particles concentration. Continuous mixture model with algebraic equation for particles slipping velocity is used. Two hydrodynamic regimes are considered: axial flow without drill pipe rotation and with drill pipe rotation. In the case of axial flow was shown that increasing of power index n and consistency factor k increases pressure gradient and decreases cuttings concentration. Increasing of yield stress leads to increasing of pressure gradient and cuttings concentration. Cuttings concentration achieves constant value for high yield stress and not depends on it. Rotation of the drill pipe significantly changes the flow structure: pressure loss occurs and particles concentration decreases in the cross section. Two basic regimes of rotational flow are observed: domination of primary vortex around drill pipe and domination secondary vorticity structures. Transition between regimes leads to significant changes of flow integral parameters.

9 June 2019
Verified
Conference Paper
Closed access
PDF file
YIYaroslav Ignatenko
Yaroslav Ignatenko
AGAndrey Gavrilov
Andrey Gavrilov
OBOleg Bocharov
Oleg Bocharov
RMRoland May
Roland May
An Eulerian mixture model of the two-phase flow was used for cuttings transport simulation. The model was tested using experimental data for particles transport in pipes. Three types of problem statements were analyzed: steady-state flow, non-stationary flow in a short-length channel with periodic boundary conditions, and non-stationary flow in a long channel. Simulation of cuttings transport by Herschel-Bulkley fluid through an inclined 21-inch borehole/–6.5-inch drillpipe annulus was performed. All problem statements showed very close results, even for unsteady flow. These results demonstrated the applicability of 2D steady-state problem formulation for cuttings transport simulation. The unsteady flow was observed for an inclination of less than 20 degrees. Slow downward sliding of cuttings in the lower part of inclined boreholes was observed simultaneously with upstream dunes movement. Drill pipe rotation significantly decreased the cuttings concentration and pressure gradient, and shifted the maximum cuttings transport downward sliding rate from a 20- to 40-degree inclination.

5 March 2024 in Fluids
Verified
Journal Article
Open access
PDF file
ASAlexander Viktorovich Seryakov
Alexander Viktorovich Seryakov
YIYaroslav Ignatenko
Yaroslav Ignatenko
OBOleg B. Bocharov
Oleg B. Bocharov
A numerical simulation of the Herschel–Bulkley laminar steady state shear flow around a stationary particle located on a sedimentation layer was carried out. The surface of the sedimentation layer was formed by hemispheres of the same radius as the particle. The drag force, lift force, and torque values were obtained in the following ranges: shear Reynolds numbers for a particle ReSH=2–200, corresponding to laminar flow; power law index n=0.6–1.0; and Bingham number Bn=0–10. A significant difference in the forces and torque acting on a particle in shear flow in comparison to the case of a smooth wall is shown. It is shown that the drag coefficient is on average 6% higher compared to a smooth wall for a Newtonian fluid but decreases with the increase in non-Newtonian properties. At the edge values of n=0.6 and Bn=10, the drag is on average 25% lower compared to the smooth wall. For a Newtonian fluid, the lift coefficient is on average 30% higher compared to a smooth wall. It also decreases with the increase in non-Newtonian properties of the fluid, but at the edge values of n=0.6 and Bn=10, it is on average only 3% lower compared to the smooth wall. Approximation functions for the drag, lift force, and torque coefficient are constructed. A reduction in the drag force and lifting force leads to an increase in critical stresses (Shields number) on the wall on average by 10% for incipient motion (rolling) and by 12% for particle detachment from the sedimentation bed.