Graphene in its pristine form has demonstrated a gas detection ability in an inert carrier gas. For practical use in ambient atmosphere, its sensor properties should be enhanced with functionalisation by defects and dopants, or by decoration with nanophases of metals or/and metal oxides. Excellent sensor behaviour was found for two types of single layer graphenes: grown by chemical vapour deposition (CVD) and transferred onto oxidized silicon (Si/SiO2/CVDG), and the epitaxial graphene grown on SiC (SiC/EG). Both graphene samples were functionalised using a pulsed laser deposited (PLD) thin V2O5 layer of average thickness ≈ 0.6 nm. According to the Raman spectra, the SiC/EG has a remarkable resistance against structural damage under the laser deposition conditions. By contrast, the PLD process readily induces defects in CVD graphene. Both sensors showed remarkable and selective sensing of NH3 gas in terms of response amplitude and speed, as well as recovery rate. SiC/EG showed a response that was an order of magnitude larger as compared to similarly functionalised CVDG sensor (295% vs. 31% for 100 ppm NH3). The adsorption site properties are assigned to deposited V2O5 nanophase, being similar for both sensors, rather than (defect) graphene itself. The substantially larger response of SiC/EG sensor is probably the result of the smaller initial free charge carrier doping in EG.
Miniature and low-power gas sensing elements are urgently needed for a portable electronic nose, especially for outdoor pollution monitoring. Hereby we prepared chemiresistive sensors based on wide-area graphene (grown by chemical vapor deposition) placed on Si/Si3N4 substrates with interdigitated electrodes and built-in microheaters. Graphene of each sensor was individually functionalized with ultrathin oxide coating (CuO-MnO2, In2O3 or Sc2O3) by pulsed laser deposition. Over the course of 72 h, the heated sensors were exposed to randomly generated concentration cycles of 30 ppb NO2, 30 ppb O3, 60 ppb NO2, 60 ppb O3 and 30 ppb NO2 + 30 ppb O3 in synthetic air (21% O2, 50% relative humidity). While O3 completely dominated the response of sensors with CuO-MnO2 coating, the other sensors had comparable sensitivity to NO2 as well. Various response features (amplitude, response rate, and recovery rate) were considered as machine learning inputs. Using just the response amplitudes of two complementary sensors allowed us to distinguish these five gas environments with an accuracy of ~ 85%. Misclassification was mostly due to an overlap in the case of the 30 ppb O3, and 30 ppb O3 + 30 ppb NO2 responses, and was largely caused by the temporal drift of these responses. The addition of recovery rates to machine learning input variables enabled us to very clearly distinguish different gases and increase the overall accuracy to ~94%.
Gas sensing properties of Co-oxide thin films were investigated and modelled. The films of cubic Co3O4 structure and with thickness between 20-150 nm were fabricated by pulsed laser deposition. The response of dc-conductivity to different gases (CO, NO2, CH4) was tested at temperatures 240 - 400 °C, and at different oxygen pressures. The conductivity changes due to O2 and due to test gas were found to be almost independent. The commonly used ionosorption model, which assumes reactions with adsorbed oxygen ions, failed to describe the dataset obtained at different CO and O2 pressures. Alternative mechanisms are discussed
Chemiresistive gas sensors were produced by functionalizing graphene with a ~3 nm layer of mixed oxide xCu2O⸱yMnO using pulsed laser deposition (PLD) from a hopcalite CuMn2O4 target. Sensor response time traces were recorded for strongly oxidizing (NO2, O3) and reducing (NH3, H2S) poisonous gases at ppb and ppm levels, respectively. The morphology of the MOX layer was modified by growth temperature during PLD, resulting in the optimization of the sensor response. Differences in decomposition or oxidation rates on catalytically active metal oxide (MOX) were utilized to achieve partial selectivity for pairs of gases that have similar adsorption and redox properties. The predominant selectivity towards ozone in most samples at different measuring conditions remained difficult to suppress. A distinct selectivity for H2S emerged at higher measurement temperatures (100–150 °C), which was assigned to catalytic oxidation with O2. Several gas–MOX interaction mechanisms were advanced to tentatively explain the sensor behavior, including reversible electron transfer in the simplest case of NO2, decomposition via ionic transients for O3, and complex catalytic oxidative transformations for NH3 and H2S.
Exceptionally sensitive and selective graphene-based chemiresistive gas sensors were produced as a result of graphene functionalisation with a sub-nanometer V2O5 layer by using the method of pulsed laser deposition. Two different types of graphene were used—epitaxial graphene on SiC and CVD graphene on Si/SiO2—and both showed remarkable enhancement of sensing properties in terms of response and recovery speed, response magnitude and selectiveness towards NH3 gas. The epitaxial graphene-based sensor was demonstrating the highest relative response towards ammonia amounting to 80% for 0.1 ppm NH3.