Graphene in its pristine form has demonstrated a gas detection ability in an inert carrier gas. For practical use in ambient atmosphere, its sensor properties should be enhanced with functionalisation by defects and dopants, or by decoration with nanophases of metals or/and metal oxides. Excellent sensor behaviour was found for two types of single layer graphenes: grown by chemical vapour deposition (CVD) and transferred onto oxidized silicon (Si/SiO2/CVDG), and the epitaxial graphene grown on SiC (SiC/EG). Both graphene samples were functionalised using a pulsed laser deposited (PLD) thin V2O5 layer of average thickness ≈ 0.6 nm. According to the Raman spectra, the SiC/EG has a remarkable resistance against structural damage under the laser deposition conditions. By contrast, the PLD process readily induces defects in CVD graphene. Both sensors showed remarkable and selective sensing of NH3 gas in terms of response amplitude and speed, as well as recovery rate. SiC/EG showed a response that was an order of magnitude larger as compared to similarly functionalised CVDG sensor (295% vs. 31% for 100 ppm NH3). The adsorption site properties are assigned to deposited V2O5 nanophase, being similar for both sensors, rather than (defect) graphene itself. The substantially larger response of SiC/EG sensor is probably the result of the smaller initial free charge carrier doping in EG.
7 March 2017 in Beilstein Journal of Nanotechnology
Graphene has been recognized as a promising gas sensing material. The response of graphene-based sensors can be radically improved by introducing defects in graphene using, for example, metal or metal oxide nanoparticles. We have functionalised CVD grown, single-layer graphene by applying pulsed laser deposition (PLD) of V2O5 which resulted in a thin V2O5 layer on graphene with average thickness of ≈0.6 nm. From Raman spectroscopy, it was concluded that the PLD process also induced defects in graphene. Compared to unmodified graphene, the obtained chemiresistive sensor showed considerable improvement of sensing ammonia at room temperature. In addition, the response time, sensitivity and reversibility were essentially enhanced due to graphene functionalisation by laser deposited V2O5. This can be explained by an increased surface density of gas adsorption sites introduced by high energy atoms in laser ablation plasma and formation of nanophase boundaries between deposited V2O5 and graphene.
Miniature and low-power gas sensing elements are urgently needed for a portable electronic nose, especially for outdoor pollution monitoring. Hereby we prepared chemiresistive sensors based on wide-area graphene (grown by chemical vapor deposition) placed on Si/Si3N4 substrates with interdigitated electrodes and built-in microheaters. Graphene of each sensor was individually functionalized with ultrathin oxide coating (CuO-MnO2, In2O3 or Sc2O3) by pulsed laser deposition. Over the course of 72 h, the heated sensors were exposed to randomly generated concentration cycles of 30 ppb NO2, 30 ppb O3, 60 ppb NO2, 60 ppb O3 and 30 ppb NO2 + 30 ppb O3 in synthetic air (21% O2, 50% relative humidity). While O3 completely dominated the response of sensors with CuO-MnO2 coating, the other sensors had comparable sensitivity to NO2 as well. Various response features (amplitude, response rate, and recovery rate) were considered as machine learning inputs. Using just the response amplitudes of two complementary sensors allowed us to distinguish these five gas environments with an accuracy of ~ 85%. Misclassification was mostly due to an overlap in the case of the 30 ppb O3, and 30 ppb O3 + 30 ppb NO2 responses, and was largely caused by the temporal drift of these responses. The addition of recovery rates to machine learning input variables enabled us to very clearly distinguish different gases and increase the overall accuracy to ~94%.
In this manuscript, we explore the sensor properties of epitaxially grown graphene on silicon carbide decorated with nanolayers of CuO, Fe3O4, V2O5, or ZrO2. The sensor devices were investigated in regard to their response towards NH3 as a typical reducing gas and CO, C6H6, CH2O, and NO2 as gases of interest for air quality monitoring. Moreover, the impact of operating temperature, relative humidity, and additional UV irradiation as changes in the sensing environment have been explored towards their impact on sensing properties. Finally, a cross-laboratory study is presented, supporting stable sensor responses, and the final data is merged into a simplified sensor array. This study shows that sensors can be tailored not only by using different materials but also by applying different working conditions, according to the requirements of certain applications. Lastly, a combination of several different sensors into a sensor array leads to a well-performing sensor system that, with further development, could be suitable for several applications where there is no solution on the market today.
Chemiresistive gas sensors were produced by functionalizing graphene with a ~3 nm layer of mixed oxide xCu2O⸱yMnO using pulsed laser deposition (PLD) from a hopcalite CuMn2O4 target. Sensor response time traces were recorded for strongly oxidizing (NO2, O3) and reducing (NH3, H2S) poisonous gases at ppb and ppm levels, respectively. The morphology of the MOX layer was modified by growth temperature during PLD, resulting in the optimization of the sensor response. Differences in decomposition or oxidation rates on catalytically active metal oxide (MOX) were utilized to achieve partial selectivity for pairs of gases that have similar adsorption and redox properties. The predominant selectivity towards ozone in most samples at different measuring conditions remained difficult to suppress. A distinct selectivity for H2S emerged at higher measurement temperatures (100–150 °C), which was assigned to catalytic oxidation with O2. Several gas–MOX interaction mechanisms were advanced to tentatively explain the sensor behavior, including reversible electron transfer in the simplest case of NO2, decomposition via ionic transients for O3, and complex catalytic oxidative transformations for NH3 and H2S.
Low-power gas sensors that can be used in IoT (Internet of Things) systems, consumer devices, and point-of-care devices will enable new applications in environmental monitoring and health protection. We fabricated a monolithic chemiresistive gas sensor by integrating a micro-lightplate with a 2D sensing material composed of single-layer graphene and monolayer-thick TiO2. Applying ultraviolet (380 nm) light with quantum energy above the TiO2 bandgap effectively enhanced the sensor responses. Low (<1 μW optical) power operation of the device was demonstrated by measuring NO2 gas at low concentrations, which is typical in air quality monitoring, with an estimated limit of detection < 0.1 ppb. The gas response amplitudes remained nearly constant over the studied light intensity range (1–150 mW/cm2) owing to the balance between the photoinduced adsorption and desorption processes of the gas molecules. The rates of both processes followed an approximately square-root dependence on light intensity, plausibly because the electron–hole recombination of photoinduced charge carriers is the primary rate-limiting factor. These results pave the way for integrating 2D materials with micro-LED arrays as a feasible path to advanced electronic noses.