Yue Dong

Yue Dong


Research Focus & Metrics

Academic Career Length

4Years (2023-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
17 June 2024 in IEEE Transactions on Instrumentation and Measurement
Verified
Journal Article
Closed access
FSFazhi Song
Fazhi Song
YLYang Liu
Yang Liu
YDYue Dong
Yue Dong
XCXinkai Chen
Xinkai Chen
JTJiubin Tan
Jiubin Tan
Accurate pattern transfer, coupled with stringent requirements for throughput and quality in lithography systems, necessitates the wafer scanner executing an aggressive motion with the tracking error in terms of nanometers. This underscores the need for advanced control technologies. The aim of this paper is to identify motion control issues in wafer scanners taking the accuracy requirement as well as the mechatronic dynamics into account, and then investigate the control methods for plants with diverse dynamics. Motion control aspects that will be discussed include: i) setpoint generator that creates smooth motion profiles through trajectory planning and input shaping, ii) multi-DOF decoupling control with static and dynamic design, iii) single DOF motion control utilizing the combination of linear/nonlinear feedback and model/data-based feedforward, and iv) multi-stage coordination control for the synchronized motion between wafer stage (WS) and reticle stage (RS), short-stroke module (SSM) and long-stroke module (LSM), as well as LSM and balance mass (BM). The control challenges associated with these aspects mainly involve: 1) cross-talk behaviors among motion DOFs, 2) flexible modes in the mechatronic dynamics, 3) model uncertainties, 4) stochastic and non-stochastic disturbances/noise, and 5) inherent design tradeoffs like Bode’s sensitivity integral. Both long-known and next-generation motion control methods are investigated and discussed with appropriate insightful comments.

14 August 2024 in IEEE Transactions on Automation Science and Engineering
Verified
Journal Article
Closed access
KLKaixin Liu
Kaixin Liu
FSFazhi Song
Fazhi Song
YDYue Dong
Yue Dong
YLYang Liu
Yang Liu
JTJiubin Tan
Jiubin Tan
Decoupling control is a widely employed technique used to mitigate coupling effects and bridge the gap between multiple-input multiple-output (MIMO) and single-input single-output (SISO) control. In the field of precision motion control, the cross-talk resulting from coarse decoupling poses a significant challenge to achieving high performance. Static decoupling control fails to completely decouple the MIMO system due to dynamic disparities between drives, actuators, and the flexible modes of the plant. Consequently, dynamic decoupling control methods have gained attention for their potential to enhance performance. However, existing dynamic decoupling control methods suffer from limitations such as reliance on system models, and susceptibility to disturbances and noise. In this paper, these deficiencies are addressed by 1) a data-based optimization with no involvement of model knowledge, and 2) using the augmented vector and instrumental variable to eliminate the estimation bias caused by position-dependent disturbances and measurement noise. The effectiveness and superiority of the proposed method are substantiated through numerical simulations and experiments conducted on an ultra-precision wafer stage. Note to Practitioners —This paper presents a non-iterative dynamic decoupling method, which is suitable for LTI multivariable systems with stringent precision requirements, such as the wafer stage and the atomic force microscope. In the field of precision motion control, the feedback controller plays a crucial role in the stability and robustness of the system. However, to achieve the desired performance, additional methods may be necessary, such as feedforward control method, nonlinear control method, etc. Especially for multiple-input multiple-output systems, it is essential to maintain high decoupling accuracy to avoid the cross-talk, which emerges due to a coarse decoupling. Given the practical differences in dynamic characteristics between drives and actuators, as well as non-rigid modes in the system, dynamic decoupling is recommended over static decoupling. Furthermore, it is promising to develop a data-based method that enables inevitable uncertainties between the model and the actual plant. In the dynamic decoupling method proposed in this paper, the impact of position-dependent disturbances and the measurement noise are jointly taken into consideration, which has not been previously addressed in literature. The augmented vector and instrumental variable are introduced to eliminate the adverse effects of these irrelevant data. Consequently, an unbiased estimate of the dynamic decoupling controller can be obtained. The practicality and effectiveness of the proposed method have been demonstrated. In future work, we will focus on the optimal selection of the dynamic decoupling controller under bounded disturbances and its application to redundant systems.

11 October 2024 in ISA Transactions
Verified
Journal Article
Closed access
HZHongyang Zhao
Hongyang Zhao
YWYu Wan
Yu Wan
LLLi Li
Li Li
YDYue Dong
Yue Dong
NCNing Cui
Ning Cui
YLYang Liu
Yang Liu

28 September 2023 in Applied Sciences
Verified
Journal Article
Open access
PDF file
YLYang Liu
Yang Liu
QMQian Miao
Qian Miao
YDYue Dong
Yue Dong
To meet the ever-increasing demand for next-generation lithography machines, the actuator plays an important role in the achievement of high acceleration of the wafer stage. However, the voice coil motor, which is widely used in high-precision positioning systems, is reaching its physical limits. To tackle this problem, a novel way to design the actuator using the magnetoresistance effect is argued due to the high force densities. However, the strong nonlinearity limits its application in the nan-positioning system. In particular, the hysteresis is coupled with eddy effects and displacement, which lead to a rate-dependent and displacement-dependent hysteresis effect in the reluctance actuator. In this paper, a Hammerstein structure is used to model the rate-dependent reluctance actuator. At the same time, the displacement-dependent of the model is regarded as the interference with the system. Additionally, a control strategy combining inverse model compensation and the disturbance observer-based discrete sliding mode control was proposed, which can effectively suppress the hysteresis effect. It is worthy pointing out that the nonlinear system is transformed into a linear system with inversion bias and disturbance by the inverse model compensation. What is more, the sliding mode controller based on the disturbance observer is designed to deal with the unmodeled dynamics, displacement disturbances, and model identification errors in linear systems. Thus, the tracking performance and robustness to external disturbances of the system are improved. The simulation results show that it is superior to the PI controller combined with an inverse compensator and even to the discrete sliding mode controller connected with inverse compensator, confirming the effectiveness of the novel control method in alleviating hysteresis.

5 June 2026 in IEEE Transactions on Industrial Electronics
Verified
Journal Article
Closed access
SSShuo Song
Shuo Song
LLLi Li
Li Li
YDYue Dong
Yue Dong
YLYang Liu
Yang Liu
JTJiubin Tan
Jiubin Tan
Iterative feedforward tuning (IFFT) plays important roles in precision motion control systems to ensure high motion performance and high task flexibility simultaneously. In this article, IFFT subject to the unknown multiplicative nonlinearity is further investigated. The proposed method adopts the inverse compensation mechanism for the multiplicative nonlinearity. Thus, a rational feedforward controller is developed with the numerator compensating for the reference trajectory and the additive disturbance and with the denominator compensating for the multiplicative nonlinearity. After feedforward parametrization, the IFFT algorithm is proposed to realize the simultaneous tuning for the numerator and denominator polynomial parameters. To enhance the convergence speed, an inner-loop iteration procedure is further utilized in each trial to obtain a more accurate data-based model required by IFFT by more fully utilizing the servo error. The superiorities of the proposed method in achieving faster, more accurate and more flexible tuning compared to relevant methods are finally verified through experimental results on a linear-motor-driven wafer stage with multiplicative force ripple.