The failure of Hall sensors can give rise to loss of rotor position and speed information, which can result in loss of control of the speed loop, spatial decoupling errors, and affecting system stability in three-phase PMSM control system. To solve this problem, a Hall fault-tolerant control system based on sensorless state switching is proposed in this paper. Firstly, a three-phase PMSM control system based on FOC is established to analyze and clarify the importance of rotor position and speed signals. Secondly, a detection scheme based on Hall change edge signal is designed to detect the health status of Hall sensors and implement fault-tolerant state switching. For the stability of the system, a sliding mode observer is built to obtain the back electromotive force(back-EMF). In addition, the phase-locked loop is designed to extract the rotor position and speed information from the back-EMF. When the system enters a fault-tolerant state, changes in the speed feedback loop can affect the control performance of the system. Therefore, the speed loop PI parameter optimization scheme based PSO algorithm is proposed to optimize the performance of the fault tolerant control system. Finally, the effectiveness of the fault-tolerant method based on the sensorless state switching after particle swarm optimization is verified on a semi-physical platform (RCP-HIL). The experimental results show that the Hall fault-tolerant control system proposed in this paper can effectively detect Hall sensor faults and cut into the fault-tolerant control state, and can maintain the control system stable during fault-tolerant state switching. Furthermore, the control system can maintain an observation error of ±30 rpm under variable load or variable speed conditions at medium and high speeds when the system enters fault-tolerant control state.
17 June 2024 in IEEE Transactions on Instrumentation and Measurement
The torque performance of permanent magnet synchronous motors (PMSMs), especially the torque output capacity and torque pulsation, which have significant impact on their efficiency and capabilities. In this paper, a novel hybrid rotor structure and improved taguchi optimization design based on fuzzy theory for PMSM torque performance enhancement are proposed. Firstly, surface and interior magnets poles are combined to proposed a new surface and interior hybrid PMSM (SIHPMSM), which adopt Halbach array and U-shape permanent magnets, respectively. In particular, an unevenly segmented and different eccentricity Halbach array is applied to optimize magnetic field performance. Secondly, the comparative analysis of typical rotor topologies is conducted, whose corresponding results indicate that SIHPMSM exhibits better electromagnetic properties. In addition, five essential variables are analyzed to further explore the affects of different parameters on torque characteristics in SIHPMSM. Finally, on the basis of Taguchi method and fuzzy theory, an improved optimization scheme is proposed, which can resolve the deficiencies of traditional Taguchi method in multi-objective optimization. Several targets including torque and torque ripple are standardized by introducing the Multiple Performance Characteristics Index (MPCI). The final optimization results significantly improve the torque output performance while reducing torque pulsations.
A sensorless control algorithm not only reduces the cost of a permanent magnet synchronous motor (PMSM) system, but also broadens its application scope. Expanding speed threshold and enhancing dynamic performance are crucial aspects. To optimize the adaptability of observers and the immunity of the controller in a full-speed domain, an improved sensorless control scheme for a PMSM based on a hybrid position observer and disturbance compensation is proposed. Firstly, the precise detection of the initial position and the scheme of starting with the load at any position are proposed based on high-frequency rotation injection, magnetic pole direction calibration and square-wave high-frequency injection (HFI). Secondly, a higher-order sliding mode observer (HSMO) is designed to improve high-speed observation performance by introducing an extended electromotive force (EEMF). Correspondingly, a speed controller called PI plus is developed utilizing a reverse control algorithm and the observed disturbance quantity, which further enhances the system’s disturbance rejection capability. Subsequently, a linearly weighted observer switching method and a linear signal withdrawal scheme are proposed to suppress torque and speed oscillations in medium-speed threshold. Furthermore, a normalized linear extended state observer (LESO) is designed to enhance rotor information estimation accuracy and enable the observation of unknown disturbances in full-speed thresholds. Finally, the effectiveness of the proposed sensorless control system is tested through experiments involving variations in speed, load, and parameter. The experimental results indicate that the proposed sensorless strategy is capable of achieving a loaded start. The designed observer switching strategy and the scheme of injection signal withdrawal contribute to a smoother acceleration process. Furthermore, load variation test results at high-speed thresholds demonstrate that the proposed controller can reduce speed drop by 45 rpm compared to a traditional PI. Additionally, the results of parameter variation testing validate the observer’s robustness in the disturbances of within the range of ±0.3 pu.