In the field of vibration and noise reduction, micro-perforated panel (MPP) structures and Helmholtz resonators (HR) play crucial roles as common sound-absorbing elements. However, independently applied MPP and HR structures cannot provide sufficiently wide absorption bandwidths at low frequencies. To achieve low-frequency broadband sound absorption, this study proposes a novel low-frequency broadband sound absorption structure (EMH) based on MPP and HR with a thickness of 40 mm to achieve a subwavelength, efficient, and compact design. We establish theoretical models of MPP and HR coupled systems, systematically analyze the sound absorption performance of same-element and different-element coupled structures, and employ the particle swarm optimization (PSO) algorithm to obtain structural parameters for efficient coupled sound absorption. Furthermore, we compare the sound absorption performance of three optimized coupled structures (MPP-coupled (SM), HR-coupled (SH), and MPP and HR-coupled) from the perspective of the theoretical calculation of the sound absorption coefficient and finite element analysis of the sound absorption mechanism. Finally, samples fabricated using 3D printing technology are tested in an impedance tube. The results demonstrate that efficient coupled sound absorption of MPP and HR can be achieved through parameter optimization. SH and SM exhibit nearly perfect sound absorption in the frequency ranges of 323–495 Hz and 615–1600 Hz, respectively, whereas the effective absorption bandwidth of EMH can reach 1225 Hz in the range of 200–1600 Hz. EMH shows superior low-frequency broadband sound absorption performance with a lightweight and simple structure, which holds the potential for application in low-frequency noise control.
In this work, a double‐layer honeycomb microperforated structure with adjustable back‐cavity’s height is designed based on cylinder honeycomb structure and microperforated panel (MPP). The sound absorption performance can be changed by adjusting the height of back‐cavity. Thus, a better absorption performance is achieved by changing the position of the inner MPP. Acoustic impedance of the structure was calculated based on transfer matrix method. The sound absorption coefficient of the structure was obtained by finite element method (FEM). Meanwhile, the 3D printing technology was used to produce the experimental samples. The experimental results demonstrate that the sound absorption coefficient of the structure is greater than 0.8 in the range of 750–1250 Hz, greater than 0.9 in the range of 2297–3592 Hz, and above 0.5 in the range of 500–4000 Hz. In addition, the feasibility of achieving adjustable sound absorption by means of changing the height of the back‐cavity is verified by theoretical, simulation, and experimental results. The structure proposed in this work can realize the function of wide‐band and better sound absorption performance by changing the position of the inner MPP, which can be applied to effectively reduce different frequencies noise.
In this study, a broadband sound absorber was developed using a double-layered irregular honeycomb microperforated panel (MPP) structure and a particle swarm optimization (PSO) algorithm to address the issue of broadband sound absorption of MPPs. An acoustic impedance model of the designed sound absorber and an optimization algorithm were implemented to obtain the structural configuration parameters for quasi-perfect sound absorption. The coupling effect between the resonant elements and the optimized structural configuration parameters enabled broadband and high-efficiency sound absorption. The impedance tube experimental results demonstrated an excellent broadband sound absorption level within the range of linear acoustics, and the designed triad and tetrad structures exhibited more than 70% absorption efficiency in the range of 609–4 002 Hz and 518–5 162 Hz, respectively. This study provides a design method and insights into the design, promotion, and application of broadband sound absorbers.
In this study, a sandwich piezoelectric nano-energy harvester model under compressive axial loading with a core layer fabricated of functionally graded (FG) porous material is presented based on the nonlocal strain gradient theory (NSGT). The von Karman type geometric nonlinearity and the axial loading were considered. The electromechanical governing equations were obtained using Hamilton’s principle. The nonlinear vibration frequencies, root mean square (RMS) voltage output and static buckling were obtained using the Galerkin method. The effects of different types of porous distribution, porosity coefficients, length scale parameters, nonlocal parameters, flexoelectricity, excitation frequencies, lumped mass and axial loads on the natural frequency and voltage output of nanobeams were investigated. Results show that the porous distributions, porosity coefficient of porous materials, the excitation frequencies and the axial load have a large effect on the natural frequency and voltage output of the sandwiched piezoelectric nanobeams. When the NSGT is considered, the critical buckling load depends on the values of the nonlocal parameters and strain gradient constants. In addition, the electromechanical conversion efficiency of the post-buckling process is significantly higher than that of the pre-buckling process. The flexoelectric effect can significantly increase the RMS voltage output of the energy harvester.
27 February 2022 in Journal of Vibration and Control
A large part of research on membrane mufflers focuses on the sound insulation performance of the membrane, and there is less research on the sound absorption performance of the membrane. In most cases, membrane mufflers only have some narrow absorption peaks in the low frequency band. In this paper, a micro-perforated dielectric elastomer membrane sound absorber is introduced to broaden the sound absorption frequency band of the membrane in the low frequency band. Different initial thickness, perforation aperture, and perforation spacing of the dielectric elastomer membranes were designed and fabricated, and the effect of the variation of the parameters was investigated by testing the sound absorption performance of the structural specimens. It was found that increasing the initial thickness of the membrane, appropriately decreasing the perforation aperture, and appropriately controlling the perforation spacing could improve the sound absorption performance of the structure. And based on the perforated membrane, a ring electrode structure was further designed to realize the electrically adjustable sound absorption frequency of the membrane. After the membrane with the ring electrode structure was perforated in the central region, the sound absorption band of the membrane was broadened significantly, and the applied voltage could realize the electrically adjustable sound absorption performance of the structure in the low frequency band.
1 December 2023 in Journal of Vibration and Control
The microperforated panel (MPP) structure is widely used in the field of noise reduction. The traditional MPP structure has a fixed absorption peak, and the optimized MPP structure has an improved absorption band, but the frequency range of the absorption is not ideal. For the design of broadband absorption in MPP structures, this paper presents a MPP acoustic absorber structure (N-MH) with an interpolated straight tube (IST) designed for superior broadband acoustic performance. The N-MH structure combines the advantages of the MPP and the embedded necked Helmholtz resonator, as well as having a sub-wavelength thickness of only 60 mm, which is only 1/14th of the wavelength at the first resonant frequency. The N-MH structure is optimized based on the particle swarm optimization (PSO) algorithm. In comparison to traditional microperforated panel structures, the N-MH structure exhibits a significantly broader sound absorption frequency band. Additionally, we thoroughly investigate the factors influencing the mid-low-frequency sound absorption performance of the N-MH structure. Through theoretical prediction, simulation analysis, and experimental testing, it is verified that the N-MH structure has excellent broadband sound absorption characteristics in the frequency interval of 0–2000 Hz, and the percentage of sound absorption bands with absorption coefficients exceeding 0.9 can reach 78.2%.