Stainless steels (SUS) and dual-phase (DP) steels have tension-compression asymmetry (TCA) in mechanical responses to full loading cycles. This phenomenon can significantly influence sheet metal forming of such metals, however, it is difficult to describe this behaviour analytically. In this research, a novel analytical method for asymmetric elastic-plastic pure bending using the Cazacu–Barlat 2004 asymmetric yield function is proposed. It only uses material parameters in tension along with an asymmetry coefficient related to the yield function. Bending operations of SUS304 and DP980 are investigated as two case studies. In the pure bending for both SUS304 and DP980, moment–curvature diagrams are analytically obtained. Furthermore, linear and nonlinear springback behaviours of SUS304 are analytically investigated. Moreover, using the analytical model as a user-defined material, a numerical model is developed for both steels under pure bending. In the V-bending case of SUS304 with and without TCA effects, the springback behaviours of the material are investigated numerically. In addition, considering friction effects, the analytical method is further modified for predicting springback behaviours in the V-bending of 16 types of SUS304 with various strengths are determined. All the analytical and numerical results have good agreement with those experimental results from literature for validation.
7 January 2022 in Journal of Energy Resources Technology
Lead-zirconate-titanate (PZT) nanoscale powder was first synthesized by the sol-gel method, then PZT and 0–3 type PZT/chrysotile fiber (CSF)/cement composite (PZTCC) wafers were fabricated after grind-mixing PZT powder with strontium carbonate and/or cement, ductile CSF in tandem with press-sintered process, respectively. The crystal structure (XRD), microstructure (SEM), piezoelectric properties after surface silver penetration, and polarization of the PZT and PZTCC wafer were investigated. Furthermore, self-sensing responses under either impulse or cyclic loading and micro-hardness toughness of PZTCC were also investigated. Results show that the incorporation of CSF and cement admixture weakens the perovskite crystalline peak of PZTCC; reduces the corresponding piezoelectric coefficient from 119.2 pC/N to 32.5 pC/N; but effectively bridges the gap on the toughness between PZTCC and concrete since the corresponding microhardness with 202.7 MPa of PZTCC is close to that of concrete. A good linear and fast electrical response against either impulse or cyclic loading of the PZTCC is achieved with their respective sensitivity, linearity, and repeatability to 1.505 mV/N, 2.42%, and 2.11%. The sensing responses and toughness of PZTCC is encouraging as an intrinsic piezoelectric sensor for real-time health monitoring of ductile concrete structures.
In this study, a sandwich piezoelectric nano-energy harvester model under compressive axial loading with a core layer fabricated of functionally graded (FG) porous material is presented based on the nonlocal strain gradient theory (NSGT). The von Karman type geometric nonlinearity and the axial loading were considered. The electromechanical governing equations were obtained using Hamilton’s principle. The nonlinear vibration frequencies, root mean square (RMS) voltage output and static buckling were obtained using the Galerkin method. The effects of different types of porous distribution, porosity coefficients, length scale parameters, nonlocal parameters, flexoelectricity, excitation frequencies, lumped mass and axial loads on the natural frequency and voltage output of nanobeams were investigated. Results show that the porous distributions, porosity coefficient of porous materials, the excitation frequencies and the axial load have a large effect on the natural frequency and voltage output of the sandwiched piezoelectric nanobeams. When the NSGT is considered, the critical buckling load depends on the values of the nonlocal parameters and strain gradient constants. In addition, the electromechanical conversion efficiency of the post-buckling process is significantly higher than that of the pre-buckling process. The flexoelectric effect can significantly increase the RMS voltage output of the energy harvester.
1 August 2018 in International Journal of Solids and Structures