Pawan Kumar Rakesh

Dr. Pawan Kumar Rakesh


Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 February 2023 in Biomass Conversion and Biorefinery
Verified
Journal Article
Closed access
PDF file
MPMayank Pokhriyal
Mayank Pokhriyal
PRPawan Kumar Rakesh
Pawan Kumar Rakesh
SMSanjay M.R.
Sanjay M.R.
Suchart SiengchinSuchart Siengchin
Suchart Siengchin

1 December 2020 in Composites Communications
Verified
Journal Article
Closed access
LRLalit Ranakoti
Lalit Ranakoti
PRPawan Kumar Rakesh
Pawan Kumar Rakesh

2 January 2023 in Expert Review of Medical Devices
Verified
Journal Article
Closed access
SBShaurya Bhatt
Shaurya Bhatt
DJDeepak Joshi
Deepak Joshi
PRPawan Kumar Rakesh
Pawan Kumar Rakesh
AGAnoop Kant Godiyal
Anoop Kant Godiyal
Traditional methods of prosthesis fabrication are not efficient and user centric and are made for common purposes without focusing on individual demands of user which leads to rejection of prosthes...

23 December 2022 in Journal of Natural Fibers
Verified
Journal Article
Open access
RKRajesh Kumar
Rajesh Kumar
PRPawan Kumar Rakesh
Pawan Kumar Rakesh
DSDungali Sreehari
Dungali Sreehari
The adverse environmental effects of synthetic fibers have forced researchers to use natural fibers in composite preparation. Pinus Roxburghii Needles (PRNs) are widely available in the hilly region of Uttarakhand state, India. Utilizing the fiber extracted from PRNs as reinforcement in bio-composite preparation can reduce synthetic fiber and emphasize the use of natural resources. In this study, we extract the Pinus Roxburghii Fibers (PRFs) from PRNs using the water retting method. Their physical, chemical, thermal, and morphological aspects were investigated and reported. The average diameter and density of the extracted PRFs were obtained as 145 ± 17.36 µm and 1020 ± 20.27 kg/m3, respectively. The chemical analysis revealed that the extracted PRFs contain 58.30% cellulose content. Thermal stability and maximum degradation temperature of the extracted PRFs were assessed using thermogravimetric analysis (TGA) and found to be 225°C and 355.84°C, respectively. Field Emission Scanning Electron Microscope (FESEM) and Atomic Force Microscope (AFM) were used to study the surface morphology and surface roughness of PRFs, respectively. Further, the FTIR analysis of the extracted PRFs confirmed the presence of different functional groups of cellulose, hemicellulose, and lignin. The crystallinity index (43.52%) and crystal size (4.03 nm) of the extracted PRFs were determined using X-ray diffraction (XRD) analysis.

28 October 2021 in Journal of Natural Fibers
Verified
Journal Article
Closed access
LRLalit Ranakoti
Lalit Ranakoti
PRPawan Kumar Rakesh
Pawan Kumar Rakesh
BGBrijesh Gangil
Brijesh Gangil
Waste collected from the agricultural sector can be used as reinforcement in the composites to lower the material cost and encourage the renewable material to reduce carbon footprints. Hence, the current investigation evaluates the physical, mechanical, and wear properties of hybrid composite laminates comprising Tasar silk waste (a waste obtained from textile industries), Jute fibers, Grewia optiva (Bhimal tree) and epoxy resin. For this, epoxy reinforced Jute/Grewia optiva fibers laminates were fabricated with varying percentages of Tasar silk waste (TSW) (0, 4, 6, 8, 10, 12, and 14 wt.%). Experimental results reveal that the void fraction increases from 1.8% to 3.4%; an increase in the water absorption took place at all percentages of TSW and become saturated after 216 hours of immersion. The tensile strength increased from 54.44 MPa to 79.16 MPa, and flexural strength increased from 21.91 MPa to 51.22 MPa with 14 wt.% of TSW. Vickers hardness and impact strength was maximum at 12 wt.% of TSW loading. Specific wear rate was observed as inversely proportional to sliding velocity, and directly proportional to normal load. Statistical analysis of the specimens was carried out using the ANOVA technique, which confirms a significant difference between the obtained results.

4 December 2020 in Journal of Adhesion Science and Technology
Verified
Journal Article
Closed access
JKJayant Kumar
Jayant Kumar
VKVipin Kumar
Vipin Kumar
ISInderdeep Singh
Inderdeep Singh
PRPawan Kumar Rakesh
Pawan Kumar Rakesh
The joining feasibility of natural fillers (wheat husk, rice husk and coir fiber) reinforced polymer composites has been studied. The different types of joints, i.e. adhesive joint (with and without hole), mechanically fastened, as well as hybrid joints (adhesive with riveting) have been analyzed in terms of their mechanical properties. The adhesive joints were found comparatively better in strength than adhesive joints with drilled hole. Anchorage effect of adhesive was found negligible in the drilled hole joint, and the joint failed at lower load due to the increase in stress concentration near the hole edge. At the same time, mechanical joining requires drilling of holes, which is still a challenging task in glass fiber reinforced plastic (GFRP) composites. The mechanical properties of the hybrid joints were found similar to adhesively bonded composites, but extension at the break in the hybrid joints was found higher than adhesively bonded joint (without hole).