The cross-linking of borates enhances the intercellular structural connection, resulting in the creation of a mechanically superior structural material composed of lignocellulose and borate. This is accomplished by employing a mechanical pretreatment procedure and a binder-free hot-pressing method. Nevertheless, these materials frequently encounter constraints in humid environments, making it challenging to simultaneously achieve the desired performance objectives. Here, the prepressed bulk of microfibrillated cellulose is modified and subjected to hot pressing, while ensuring that the enhanced physical and mechanical properties of lignocellulosic recombinant materials are maintained. This modified material is termed the microfibrillated cellulose composite laminate (MCCL). These findings indicate that the application of compression, shear, and friction forces during hot-pressing results in the formation of a compact laminated structure using pine lignocellulose. The self-cleaning MCCL exhibits significantly improved mechanical properties compared with untreated lignocellulose materials (ULM). Specifically, the flexural strength (MOR), modulus of elasticity (MOE), and internal bonding strength (IB) of self-cleaning MCCL are found to be 5 times, 2.5 times, and 4.1 times higher, respectively, than those of ULM. This improvement in the pine lignocellulose can be attributed to the enhanced layering and branching that occurs during mechanical milling. This results in a higher proportion of ester and hydrogen bonds, as well as an increased exposure of hydroxyl groups. As a result, the modified MCCL exhibits self-cleaning properties, as evidenced by its surface water contact angle (WCA) of 152°. The rolling/jumping water droplets, which contain pollutants, effectively remove graphite powder from the surface, leaving it clean. Moreover, MCCL demonstrates exceptional dimensional stability and flame-retardant self-extinguishing properties, making it highly promising as a structural material in engineering technology.

In order to study the bending properties of tropical tree species rich in organic extracts, the effects of temperature and time on the bending performance of hydrothermal treatment were investigated. The effects of power and time on bending performance under microwave heating conditions were investigated. It is found that the chemical composition does not undergo obvious degradation at 80°C–100°C, and the bending performance gradually becomes better with the increase in heating time; when the hydrothermal time exceeds 4 h, the bending performance varies with heating time. The growth is better than the difference, reaching the maximum at 4 h. When the water temperature is 140°C, the bending performance is negatively correlated with the heating time. When the hydrothermal treatment time is the same, the bending property becomes better as the temperature increases. The most reasonable process for microwave softening heating is with a power of 480 W and a heating time of 4 min. A softening treatment method combining water heat and microwave can achieve a better softening effect. When the final moisture content is controlled to 8%, the bending setting effect is the best. The optimum drying time is 6 h, and the optimum drying temperature is 50°C.

At present, the improvement of anti-wear performance of piston rings remains a challenge. In this article, Ni-SiC composite coatings fabricated at 3, 9, and 15 g/L SiC were denoted as NSc-3, NSc-9, and NSc-15 coatings. Meanwhile, the influence of SiC concentration on the surface morphology, phase structure, microhardness, and anti-wear performance of electrodeposited Ni-SiC composite coatings were investigated utilizing scanning electron microscopy, X-ray diffraction, a microhardness tester, and a friction–wear tester, respectively. The SEM images presented NSc-9 coatings with a compact, flat, or cauliflower-like surface morphology. The cross-sectional morphology and EDS results showed that the Si and Ni elements were uniformly distributed in the NSc-9 coatings with dense and flat microstructures. Moreover, the average grain size of the NSc-9 coatings was only 429 nm. Furthermore, the microhardness and indentation path of the NSc-9 coatings were 672 Hv and 13.7 μm, respectively. Also, the average friction coefficient and worn weight loss of the NSc-9 coatings were 0.46 and 29.5 mg, respectively, which were lower than those of the NSc-3 and NSc-15 coatings. In addition, a few shallow scratches emerged on the worn surfaces of the NSc-9 coatings, demonstrating their outstanding anti-wear performance when compared to the NSc-3 and NSc-15 coatings.