Attenuation and group delay effects on millimeter wave (MMW) propagation in clouds and fog are studied theoretically and verified experimentally using high resolution radar in an indoor space filled with artificial fog. In the theoretical analysis, the frequency-dependent attenuation and group delay were derived via the permittivity of the medium. The results are applied to modify the millimeter-wave propagation model (MPM) and employed to study the effect of fog and cloud on the accuracy of the Frequency-Modulated Continuous-Wave (FMCW) radar operating in millimeter wavelengths. Artificial fog was generated in the experimental study to demonstrate ultra-low visibility in a confined space. The resulted attenuation and group delay were measured using FMCW radar operating at 320–330 GHz. It was found that apart from the attenuation, the incremental group delay caused by the fog also played a role in the accuracy of the radar. The results were compared to the analytical model. It was shown that although the artificial fog has slight different characteristics compare to the natural fog and clouds, in particle composition, size, and density, the model predictions were good, pointing out that the dispersive effects should be considered in the design of remote sensing radars operating in millimeter and sub-millimeter wavelengths.

The global spread of bacterial resistance to antibiotics promotes a search for alternative approaches to eradication of pathogenic bacteria. One alternative is using photosensitizers for inhibition of Gram-positive and Gram-negative bacteria under illumination. Due to low penetration of visible light into tissues, applications of photosensitizers are currently limited to treatment of superficial local infections. Excitation of photosensitizers in the dark can be applied to overcome this problem. In the present work, dark antibacterial activity of the photosensitizer Rose Bengal alone and in combination with antibiotics was studied. The minimum inhibitory concentrations (MIC) value of Rose Bengal against S. aureus dropped in the presence of sub-MIC concentrations of ciprofloxacin, levofloxacin, methicillin, and gentamicin. Free Rose Bengal at sub-MIC concentrations can be excited in the dark by ultrasound at 38 kHz. Rose Bengal immobilized onto silicon showed good antibacterial activity in the dark under ultrasonic activation, probably because of Rose Bengal leaching from the polymer during the treatment. Exposure of bacteria to Rose Bengal in the dark under irradiation by electromagnetic radio frequency waves in the 9 to 12 GHz range caused a decrease in the bacterial concentration, presumably due to resonant absorption of electromagnetic energy, its transformation into heat and subsequent excitation of Rose Bengal.

A quasi-optical multi-ray model for a short-range millimeter wave radar is presented. The model considers multi-path effects emerging while multiple rays are scattered from the target and reflected to the radar receiver. Among the examined scenarios, the special case of grazing ground reflections is analyzed. Such a case becomes relevant when short range anti-collision radars are employed in vehicles. Such radars operate at millimeter wavelengths, and are aimed at the detection of targets located several tens of meters from the transmitter. Reflections from the road are expected to play a role in the received signal strength, together with the direct line-of-sight beams illuminated and scattered from the target. The model is demonstrated experimentally using radar operating in the W-band. Controlled measurements were done to distinguish between several scattering target features. The experimental setup was designed to imitate vehicle near-ground millimeter wave radars operating in vehicles. A comparison between analytical calculations and experimental results is made and discussed.

Design and characterization of a W-band rectenna, consisting of a 2 × 2 patch sub-array integrated with matching elements and rectifying circuitry is presented. The key element of the rectenna is a Mott diode that has permitted considerable improvement of RF-to-DC conversion efficiency in comparison with commercially available GaAs mm-wave diodes. The experimental setup was equipped by two focusing lenses, allowing a concentration of RF power within the beam spot of a 1 cm diameter at a distance of 1 m. The tuneable W-band source delivering 0.4 W RF CW power was employed to perform large-signal experiments and to measure load characteristics of the rectenna. The measured RF-to-DC conversion efficiency with the single Mott diode is approximately 17%, which is approximately 5 times higher than the commercial counterpart (Microsemi).

Controlled experiments were conducted to examine the effect of fog on signal propagation in wireless communication and radar links operating in millimeter wavelengths. The experiments were carried out in a fog laboratory to verify theoretical results obtained from Liebe’s model. Attenuation and phase shifts of millimeter wave (mmW) radiation were measured, at different fog density characterized by the visibility distance and its water vapor content. Utilizing a vector network analyzer (VNA) enabled us to examine the actual atmospheric attenuation and the phase shift caused by the fog retardation. The experimental results demonstrate good agreement with the simulations even for very low visibility in highly dense fog. The study can be used to estimate link budget of mmW wireless links, including those allocated for the fifth generation (5G) of cellular networks.

A diamond’s color grading is a dominant property that determines its market value. Its color quality is dependent on the light transmittance through the diamond and is largely influenced by nitrogen contamination, which induces a yellow/brown tint within the diamond, as well as by structural defects in the crystal (in rare cases boron contamination results in a blue tint). Generally, spectroscopic instrumentation (in the infrared or UV–visible spectral range) is used in industry to measure polished and rough diamonds, but the results are not accurate enough for precise determination of color grade. Thus, new methods should be developed to determine the color grade of diamonds at longer wavelengths, such as microwave (MV). No difference exists between rough and polished diamonds regarding stray light when the MW frequency is used. Thus, several waveguides that cover a frequency range of 3.95–26.5 GHz, as well as suitable resonator mirrors, have been developed using transmission/reflection and resonator methods. A good correlation between the S₁₂ parameter and the nitrogen contamination content was found using the transmission/reflection method. It was concluded that electromagnetic property measurements of diamonds in the MW frequency range can be used to determine their nitrogen content and color grading. The MW technique results were in good agreement with those obtained from the infrared spectra of diamonds.