Skin-attachable sensors, which represent the ultimate form of wearable electronic devices that ensure conformal contact with skin, suffer from motion artifact limitations owing to relative changes in position between the sensor and skin during physical activities. In this study, a polarization-selective structure of a skin-conformable photoplethysmographic (PPG) sensor was developed to decrease the amount of scattered light from the epidermis, which is the main cause of motion artifacts. The motion artifacts were suppressed more than 10-fold in comparison with those of rigid sensors. The developed sensor—with two orthogonal polarizers—facilitated successful PPG signal monitoring during wrist angle movements corresponding to high levels of physical activity, enabling continuous monitoring of daily activities, even while exercising for personal health care.

While the power conversion efficiencies (PCEs) of organic solar cells (OSCs) have been dramatically increased through the development of small molecular acceptors (SMAs), achieving eco-friendly solution processability of OSCs is a crucial prerequisite for their practical application. In this study, we develop three new, green solvent-processable SMAs (YSe–C3, YSe–C6, and YSe–C9) with different outer side-chains (n-propyl (C3), n-hexyl (C6), and n-nonyl (C9)), affording high-performance OSCs with non-halogenated solvent (o-xylene)-processed active layers. Also, the impact of both outer and inner side-chain engineering of these SMAs on the performance of eco-friendly fabricated OSCs is systematically investigated. The outer side-chain structure has a much more significant impact than the inner side-chain. For example, the PM6:YSe–C6 blend affords high-performance OSCs with a power conversion efficiency (PCE) of over 16%, whereas the PCEs of the YSe–C3- and YSe–C9-based OSCs are only 11–14%. The lower PCEs of PM6:YSe–C3 and C9 are mainly attributed to reduced electron mobility and increased charge recombination, resulting from aggregate-containing non-optimal blend morphologies. Interestingly, the well-optimized morphology of the YSe–C6-based blend also affords OSC devices with active layer thickness-independent PCEs, up to a thickness of >400 nm, demonstrating the great potential for large-area device manufacturing via an eco-friendly printing process. Thus, optimizing the outer side-chain structure of Y-series SMAs is essential for producing green solvent-processed high-performance OSCs.

In this study, two wide-bandgap PM7 polymer derivatives are developed via simple structural modification of the fused-accepting unit by incorporating ester groups on terthiophene at different positions (i.e., two ester groups on the outer thiophenes (PM7 D1) and on the central thiophene (PM7 D2)). This simple modification creates a higher-energy light absorption window, providing better complementary light harvesting with naphthalenediimide-based acceptor, P(NDI2HD-Se). As a result, PM7 D1-based all-polymer solar cells (all-PSCs) exhibit a high power conversion efficiency (PCE) of 9.13%, which outperforms that of the PM7-based all-PSC (PCE = 6.93%). Importantly, the ester structural modification has significant impact on the thin-film mechanical ductility and robustness. For example, elongation properties of PM7 D1 and PM7 D2 pristine films are significantly improved by ca. 2.5 times compared to that of PM7. This result is attributed to the flexible ester groups, which are able to effectively compensate for applied stress. The improved ductile properties of PM7 D1 and PM7 D2 also affect the mechanical ductility of the blend films, leading to 1.5-fold increase in crack onset strain compared with that of the PM7 blend film. Therefore, we demonstrate that the introduction of ester groups in conjugated polymers provides a simple and promising strategy for future stretchable electronics.

Biological compounds often provide clues to advance material designs. Replicating their molecular structure and functional motifs in artificial materials offers a blueprint for unprecedented functionalities. Here, we report a flexible biomimetic thermal sensing (BTS) polymer that is designed to emulate the ion transport dynamics of a plant cell wall component, pectin. Using a simple yet versatile synthetic procedure, we engineer the physicochemical properties of the polymer by inserting elastic fragments in a block copolymer architecture, making it flexible and stretchable. The thermal response of our flexible polymer outperforms current state-of-the-art temperature sensing materials, including vanadium oxide, by up to two orders of magnitude. Thermal sensors fabricated from these composites exhibit a sensitivity that exceeds 10 mK and operate stably between 15° and 55°C, even under repeated mechanical deformations. We demonstrate the use of our flexible BTS polymer in two-dimensional arrays for spatiotemporal temperature mapping and broadband infrared photodetection.

Organic photodetectors (OPDs) offer considerable promise for low-power, solution-processable biosensing and imaging applications; however, their performance remains limited by spectral mismatch and interfacial trap states. In this study, a highly sensitive polymer photodiode was developed via trace incorporation (0.8 wt%) of InP/ZnSe/ZnS quantum dots (QDs) into a PTB7-Th:PC₇₁BM bulk heterojunction (BHJ) matrix. This QD doping approach enhanced the external quantum efficiency (EQE) across the 540–660 nm range and suppressed the dark current density at −2 V by passivating interface trap states. Despite a slight decrease in optical absorption at the optimized composition, the internal quantum efficiency (IQE) increased significantly from ~80% to nearly 95% resulting in a net EQE improvement. This suggests that QD incorporation improved charge transport without compromising charge separation efficiency. As a result, the device achieved a specific detectivity (D*) of 1.8 × 10¹³ Jones, representing a 93% improvement over binary BHJs, along with an ultra-low dark current density of 7.76 × 10⁻¹⁰ A/cm². Excessive QD loading, however, led to optical losses and increased dark current, underscoring the need for precise compositional control. Furthermore, the enhanced detectivity led to a 4 dB improvement in the signal-to-noise ratio (SNR) of photoplethysmography (PPG) signals in the target wavelength range, enabling more reliable biophotonic sensing without increased power consumption. This work demonstrates that QD-based spectral and interfacial engineering offers an effective and scalable route for advancing the performance of OPDs, with broad applicability to low-power biosensors and high-resolution polymer–QD imaging systems.