Sustainability is a key challenge today. The high emission impact of the mobility sector requires a shift from internal combustion engines to electric traction motors. In order to improve sustainability holistically, the entire lifecycle from raw materials, manufacturing, use and end-of-life must be considered during development. Although a lot can be carried out to influence sustainability during the development phase, knowledge about the product is still very limited. Considering the main lifecycle stages already during the development phase requires a systematic development approach. Furthermore, integrating data from previous product generations is required. Generating a digital twin which collects data over the lifecycle is a useful tool which enables the prediction of evaluation criteria for the lifecycle stages. However, when using the digital twin, a suitable description model needs to be generated. A cross-lifecycle evaluation model based on Life Cycle Costing (LCC) and Life Cycle Assessment (LCA) was used to evaluate sustainability throughout the whole lifecycle. Information for evaluation was generated using a cross-lifecycle modeling approach, which enabled the combination of different lifecycle perspectives during development. To show the potential of evaluating different solutions from different perspectives, the methodology was demonstrated with a lightweight rotor of an electric traction motor. The great potential of the process model is shown.

This paper presents the thermal analysis of a novel laser sintering machine for additive manufacturing of continuous carbon fibre-reinforced polymer parts. The core element of this machine is a fibre integration unit with a heated fibre nozzle. With the help of an additional heat source, which is mounted on the bottom side of the fibre integration unit, the temperature of the powder bed surface is kept within the sintering window of the PA12 material used in the investigations. Different heat source variants differing in shape and material were analysed experimentally concerning the heat distribution achieved within the powder bed surface using an infrared camera. Based on the best-rated variant showing the most homogeneous heat distribution, operating points for successful continuous fibre integration were experimentally identified. An aluminium plate with a closed fibre nozzle slot and symmetrical surface heating power has proven to keep the powder bed surface reliably warm. Compared to the initial state, the resulting increased uniformity of heat-affected zones created by the heated fibre nozzle HAZ was evaluated by fabricating a horseshoe part made of PA12. Furthermore, a CCFRP flat pedal for mountain bikes demonstrated roving integration’s process reliability and reproducibility.

Continuous fiber-reinforced polymer (CoFRP) parts offer significant potential for reducing future product consumption and CO₂ emissions due to their high tensile properties and low density. Additive manufacturing enables the tool-free production of complex geometries with optimal material utilization, making it a promising approach for creating load-path-optimized CoFRP parts. Recent advancements have integrated continuous fibers into laser sintering processes, allowing for the support-free production of complex parts with improved material properties. However, additive manufacturing faces challenges such as long production times, small component dimensions, and defects like high void content. New processes, including Arburg Polymer Freeforming (APF), robotic direct extrusion (DES) and the integration of thermoplastic tapes, and laser sintering, have enabled the production of CoFRPs to address these issues. A comparison of these new processes with existing material extrusion methods is necessary to determine the most suitable approach for specific tasks. The fulfillment factor is used to compare composites with different matrix and fiber materials, representing the percentage of experimentally achieved material properties relative to the theoretical maximum according to the Voigt model. The fulfillment factor varies significantly across different processes and materials. For FFF processes, the fulfillment factor ranges from 20% to 77% for stiffness and 14% to 84% for strength, with an average of 52% and 37%, respectively. APF shows a high fulfillment factor for stiffness (94%) but is lower for strength (23%), attributed to poor fiber–matrix bonding and process-induced pores. The new DES process improves the fulfillment factor due to additional consolidation steps, achieving above-average values for strength (67%). The CoFRP produced by the novel LS process also shows a high fulfillment factor for stiffness (85%) and an average fulfillment factor for strength (39%), influenced by suboptimal process parameters and defects.

Additive manufacturing using continuous carbon-fibre-reinforced polymer (CCFRP) presents an opportunity to create high-strength parts suitable for aerospace, engineering, and other industries. Continuous fibres reinforce the load-bearing path, enhancing the mechanical properties of these parts. However, the existing additive manufacturing processes for CCFRP parts have numerous disadvantages. Resin- and extrusion-based processes require time-consuming and costly post-processing to remove the support structures, severely restricting the design flexibility. Additionally, the production of small batches demands considerable effort. In contrast, laser sintering has emerged as a promising alternative in industry. It enables the creation of robust parts without needing support structures, offering efficiency and cost-effectiveness in producing single units or small batches. Utilising an innovative laser-sintering machine equipped with automated continuous fibre integration, this study aims to merge the benefits of laser-sintering technology with the advantages of continuous fibres. The paper provides an outline, using a finite element model in COMSOL Multiphysics, for simulating and identifying an optimised operating point range for the automated integration of continuous fibres. The results demonstrate a remarkable reduction in processing time of 233% for the fibre integration and a reduction of 56% for the width and 44% for the depth of the heat-affected zone compared to the initial setup.

Batteriekalander werden aktuell manuell, erfahrungsbasiert und zeitintensiv iterativ beim Start einer neuen Produktionskampagne eingestellt und bei Bedarf während der Produktion nachjustiert. Bei einer variantenreichen und agilen Produktion tritt dieser Anlaufprozess im Gegensatz zu einer auf ein Produkt spezialisierten Großserienproduktion vermehrt auf. Ein Anlagen- und Automatisierungskonzept für einen schnelleren Produktionsanlauf von Batteriekalandern wird im Folgenden vorgestellt. Battery calenders are currently set manually, experience-based and time-intensively iteratively at the start of a new production campaign and are readjusted as required during production. In a variant-rich and agile production, this start-up process occurs more frequently in contrast to a large-scale production specialized on one product. A plant and automation concept for faster production startup of battery calenders is presented below.