Tommaso Seresini

Mr. Tommaso Seresini

orcid

Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 May 2022 in AIP Advances
Verified
Journal Article
Open access
PDF file
PYPeilong Yuan
Peilong Yuan
SSSevilia Sunetchiieva
Sevilia Sunetchiieva
LLLiwang Liu
Liwang Liu
SLShiyuan Liu
Shiyuan Liu
TSTommaso Seresini
Tommaso Seresini
CGChrist Glorieux
Christ Glorieux
Early detection and monitoring of heavy load induced plastic deformation in the structure is crucial for timely intervention before cracking occurs and the material completely fails. Ultrasound can be used for detecting plastic deformation provided the mechanical modulus, which can be probed via changes in velocities. This work presents a measurement scheme that makes use of optically detected, laser-induced surface acoustic waves (SAWs) for remote, real-time, online monitoring of the wave velocity during the elastic–plastic transition occurring in an aluminum plate undergoing a uniaxial tensile test and a dynamic fatigue test. Monochromatic SAWs were photoacoustically generated in a wavelength-controlled way through a transient thermal grating based laser ultrasonics excitation scheme. The SAWs were detected by a home-built photorefractive interferometer. The results reveal both regions of acceleration and slowing down, indicating that the material first stiffens and then starts to form microcracks that make it behave effectively softer for propagating SAWs.

1 October 2023 in Vibration
Verified
Journal Article
Open access
PDF file
TSTommaso Seresini
Tommaso Seresini
SSSevilia Sunetchiieva
Sevilia Sunetchiieva
HPHelge Pfeiffer
Helge Pfeiffer
MWMartine Wevers
Martine Wevers
CGChrist Glorieux
Christ Glorieux
Laser Doppler scanning vibrometry is used for imaging spectral vibration components in a carbon fiber-reinforced composite plate that contains a sub-surface delamination defect caused by hammer impact. The images reveal sideband generation at the location of the defect, reflecting mechanical nonlinearity-induced mixing between a high amplitude, low-frequency vibration that modulates the stress–strain behavior near the defect and a low amplitude, high-frequency probe vibration. In this work, a multifrequency probe is used to tackle the problem that the mixing coefficients are, in practice, frequency dependent. Based on the measured sideband amplitudes, a study is presented on the expected feasibility of detecting defects by a full field imaging scheme based on a photorefractive interferometer that is configured as a vibrometer acting as a bandpass filter around a sideband frequency of interest.

31 August 2021 in Photoacoustics
Verified
Journal Article
Open access
YLYang Liu
Yang Liu
TSTommaso Seresini
Tommaso Seresini
Junyan LiuJunyan Liu
Junyan Liu
LLLiwang Liu
Liwang Liu
FWFei Wang
Fei Wang
CGChrist Glorieux
Christ Glorieux
Light absorption induced thermoelastic and photoacoustic excitation, combined with laser Doppler vibrometry, was utilized to analyze the dynamic mechanical behavior of a microcantilever. The measured frequency response, modal shapes, and acoustic coupling effects were interpreted in the framework of a simple Bernouilli-Euler model and quantitative 3D finite element method (FEM) analysis. Three opto-mechanical generation mechanisms, each initiated by modulated optical absorption and heating, were identified both by an analytical and finite element model. In decreasing order of importance, optically induced cantilever bending is found to be caused by: (i) differences in photoacoustically induced pressure oscillations in the air adjacent to the illuminated and dark side of the cantilever, resulting from heat transfer from the illuminated cantilever to the nearby air, acting as a volume velocity piston, and (ii) thermoelastic stresses accompanying temperature and thermal expansion gradients in the cantilever, (iii) photoacoustically induced pressure oscillations in the air adjacent to the illuminated cantilever holder and frame.

1 January 2019 in Proceedings of Meetings on Acoustics
Verified
Conference Paper
Open access
PDF file
PYPeilong Yuan
Peilong Yuan
LHLisha Huo
Lisha Huo
TSTommaso Seresini
Tommaso Seresini
YLYang Liu
Yang Liu
SSSevilia Sunetchiieva
Sevilia Sunetchiieva
CGChrist Glorieux
Christ Glorieux
Laser-based ultrasonic inspection is an emerging versatile non-contact technique for defect detection in a variety of critical components. This article reports on the adaptation of this method for the inspection of rotating cylindrical components undergoing varying stress, by detecting the dynamically changing mechanical response of cracks, which goes along with modulation of the guided acoustic waves that encounter the cracks. Optical interferometry was used for the remote detection of photo-acoustically generated guided waves. An application of laser ultrasonic to investigate guided waves and their interaction with cracks detected by a laser Doppler velocimetry (LDV) on cylindrical structures under dynamically changing stress is presented. Mode conversion, which occurs when guided waves are encountering a crack, is also investigated. The experimentally assessed effects of defects on the envelope, spectrum and other receiving wave characteristics are analysed and exploited for their detection and characterization, giving a basis for the use of laser ultrasonic for Non Destructive Testing (NDT).