All solid-state batteries offer the possibility of increased safety at potentially higher energy densities compared to conventional lithium-ion batteries. In an all-ceramic oxide battery, the composite cathode consists of at least one ion-conducting solid electrolyte and an active material, which are typically densified by sintering. In this study, the reaction of the solid electrolyte Li1.3Al0.3Ti1.7(PO4)3 (LATP) and the active material LiNi0.6Co0.2Mn0.2O2 (NCM622) is investigated by cosintering at temperatures between 550 and 650 °C. The characterization of the composites and the reaction layer is performed by optical dilatometry, X-ray diffractometry, field emission scanning electron microscopy with energy dispersive X-ray spectroscopy, time-of-flight secondary ion mass spectrometry, as well as scanning transmission electron microscopy (STEM). Even at low sintering temperatures, elemental diffusion occurs between the two phases, which leads to the formation of secondary phases and decomposition reactions of the active material and the solid electrolyte. As a result, the densification of the composite is prevented and ion-conducting paths between individual particles cannot be formed. Based on the experimental results, a mechanism of the reactions in cosintered LATP and NCM622 oxide composite cathodes is suggested.
To achieve cohesive interfaces of solid components in next‐generation Li‐ion batteries (LIBs) composed of oxide cathodes and solid electrolytes (SEs) high‐temperature sintering is necessary which leads to material degradation and phase decompositions. Thermochemically compatible components can address these issues. In this work, advanced electron microscopy techniques are employed to investigate the structural and chemical evolution taking place at the interfaces between a LiFePO4 (LFP) cathode and an in‐house optimized Li1.3Al0.3Ti1.7(PO4)3 (LATP) SE co‐sintered between 650 °C – 850 °C. While the LFP particles exhibit excellent structural stability, the LATP particles phase transforms at elevated temperatures. At 650 °C, FeLi anti‐site defect is observed at the LFP grain boundaries. Between 750 and 850 °C, the LATP (R‐3c) transforms into two orthorhombic phases (Pbca and Pbcn) of the type Li1.3+xAl0.3FexTi1.7‐x(PO4)3 depending on Fe substitution while forming the cohesive interfaces. The discharge capacity of the composite decreases from 148 mAh g−1 at 650 °C to 130 mAh g‐1 at 850 °C confirming that the new phases are still electrochemically active. This study provides a spatially resolved insight into the formation of cohesive interfaces highlighting the advantage of employing components with similar anionic structures for further improvements in LIBs.
Solid-state batteries (SSBs) with Li-ion conductive electrolytes made from polymers, thiophosphates (sulfides) or oxides instead of liquid electrolytes have different challenges in material development and manufacturing. For oxide-based SSBs, the co-sintering of a composite cathode is one of the main challenges. High process temperatures cause undesired decomposition reactions of the active material and the solid electrolyte. The formed phases inhibit the high energy and power density of ceramic SSBs. Therefore, the selection of suitable material combinations as well as the reduction of the sintering temperatures are crucial milestones in the development of ceramic SSBs. In this work, the co-sintering behavior of Li1.3Al0.3Ti1.7(PO4)3 (LATP) as a solid electrolyte with Li-ion conductivity of ≥0.38 mS/cm and LiFePO4 with a C-coating (LFP) as a Li-ion storage material (active material) is investigated. The shrinkage behavior, crystallographic analysis and microstructural changes during co-sintering at temperatures between 650 and 850 °C are characterized in a simplified model system by mixing, pressing and sintering the LATP and LFP and compared with tape-casted composite cathodes (d = 55 µm). The tape-casted and sintered composite cathodes were infiltrated by liquid electrolyte as well as polyethylene oxide (PEO) electrolyte and electrochemically characterized as half cells against a Li metal anode. The results indicate the formation of reaction layers between LATP and LFP during co-sintering. At Ts > 750 °C, the rhombohedral LATP phase is transformed into an orthorhombic Li1.3+xAl0.3−yFex+yTi1.7−x(PO4)3 (LAFTP) phase. During co-sintering, Fe3+ diffuses into the LATP phase and partially occupies the Al3+ and Ti4+ sites of the NASICON structure. The formation of this LAFTP leads to significant changes in the electrochemical properties of the infiltrated composite tapes. Nevertheless, a high specific capacity of 134 mAh g−1 is measured by infiltrating the sintered composite tapes with liquid electrolytes. Additionally, infiltration with a PEO electrolyte leads to a capacity of 125 mAh g−1. Therefore, the material combination of LATP and LFP is a promising approach to realize sintered ceramic SSBs.