The current study investigated the effect of leading-edge slats on the longitudinal stability at high angles of attack of a Blended-Wing-Body (BWB) Unmanned Air Vehicle (UAV). Using a Design of Experiments (DOE) approach and, specifically, the Taguchi method, four leading-edge slat design parameters were investigated on three different levels. These parameters were the slat semi-span, the rotation of the slat element, the extension forward of the leading edge and the downward drop below the leading edge. An L₉ orthogonal array (OA) was used to investigate the influence of these key design parameters using three performance criteria, namely the angle at which pitch break occurs, the corresponding speed and the distance between the Neutral point of each configuration and the Neutral point of the reference platform. The investigation was conducted by using high-fidelity Computational Fluid Dynamics (CFD) methods for each of the nine configurations defined by the L₉ OA, over a range of angles of attack between −4 and 16 degrees. Based on these results, and using a Signal-to-Noise ratio (SNR) analysis, two combinations were eventually derived, one that optimized pitch break angle and speed and one that optimized longitudinal stability. Finally, the Pareto Analysis of Variance (ANOVA) technique was conducted to define the contribution of each of the six design parameters on the selected performance criteria. More specifically, the semi-span seemed to have the most significant effect on pitch break angle and speed, whereas the rotation of the slat element was the most important parameter with regard to static stability.

The topic of the present study is the aerodynamic performance of a Natural Laminar Flow (NLF) wing for UAVs at low speed. The basis is a thoroughly tested NLF airfoil in the wind tunnel of NASA which is well-customized for light aircrafts. The aim of this work is the numerical verification that a typical wing design (tapered with moderate aspect ratio and wash-out), being constructed out of aerodynamically highly efficient NLF airfoils during cruise, can deliver high aerodynamic loading under minimal freestream turbulence as well as realistic atmospheric conditions of intermediate turbulence. Thus, high mission flexibility is achieved, e.g., short take off/landing capabilities on the deck of ship where moderate air turbulence is prevalent. Special attention is paid to the effect of the Wing Tip Vortex (WTV) under minimal inflow turbulence regimes. The flight conditions are take off or landing at moderate Reynolds number, i.e., one to two millions. The numerical simulation is based on an open source CFD code and parallel processing on a High Performance Computing (HPC) platform. The aim is the identification of both mean flow and turbulent structures around the wing and subsequently the formation of the wing tip vortex. Due to the purely three-dimensional character of the flow, the turbulence is resolved with advanced modeling, i.e., the Improved Delayed Detached Eddy Simulation (IDDES) which is well-customized to switch modes between Delayed Detached Eddy Simulation (DDES) and Wall-Modeled Large Eddy Simulation (WMLES), thus increasing the accuracy in the shear layer regions, the tip vortex and the wake, while at the same time keeping the computational cost at reasonable levels. IDDES also has the capability to resolve the transition of the boundary layer from laminar to turbulent, at least with engineering accuracy; thus, it serves as a high-fidelity turbulence model in this work. The study comprises an initial benchmarking of the code against wind tunnel measurements of the airfoil and verifies the adequacy of mesh density that is used for the simulation around the wing. Subsequently, the wing is positioned at near-stall conditions so that the aerodynamic loading, the kinematics of the flow and the turbulence regime in the wing vicinity, the wake and far downstream can be estimated. In terms of the kinematics of the WTV, a thorough examination is attempted which comprises its inception, i.e., the detachment of the boundary layer on the cut-off wing tip, the roll-up of the shear layer to form the wake and the motion of the wake downstream. Moreover, the effect of inflow turbulence of moderate intensity is investigated that verifies the bibliography with regard to the performance degradation of static airfoils in a turbulent atmospheric regime.

Τhe Horizon Europe and UKRI-funded MINIMAL project (no. 101056863) aims to develop climate-friendly Composite Cycle Engine (CCE) designs. This study assesses aerodynamic drag increments from new engine installations and their impact on aircraft performance through the development and the utilization of an analytical tool designed to conduct trade studies for estimating the interference drag and drag increment resulting from engine installations. This specialized analytical tool evaluates interference drag due to variations in engine position and size across three reference aircraft (short-range, medium-range, and long-range). Tool results are validated with NASA and ONERA benchmarks, demonstrating good accuracy in predicting aerodynamic impacts. Findings show a 10–15% drag increase from engine installation, offering a reliable approach to optimizing engine integration, ultimately supporting enhanced aircraft efficiency and sustainability.

This study investigates the effect of active and passive flow control devices on the aerodynamic behavior and stability of a Blended-Wing-Body (BWB) Unmanned Air Vehicle (UAV), emphasizing the low-speed segments of a typical flight. Vortilons, which are small fins placed on the leading edge of the wing, generate vortices that delay the appearance of spanwise flow and consequently the appearance of pitch break. Belly flaps are located on the underside of the UAV and can enhance the lift, while they produce a nose-up pitching moment. Seven different configurations are examined using high-fidelity Computational Fluid Dynamics (CFD) over a range of angles of attack to address the effect of each device on the lift and drag forces and the pitching moment of the UAV. Based on these results, the low-speed performance of the platform is evaluated by calculating the minimum speed, the take-off distance, and the maximum lift to drag ratio, while the elevon deflection required for the take-off rotation of the UAV is also assessed.

This study investigates the effect of passive leading-edge dogtooth extensions on the low-speed aerodynamic performance and pitch stability of a tactical Blended-Wing-Body (BWB) Unmanned Aerial Vehicle (UAV). The focus is the mitigation and the delay of the pitch break phenomenon, i.e., the sudden loss of longitudinal stability occurring at high angles of attack, during critical flight segments such as take-off and landing. A total of 15 dogtooth configurations are examined, where high-fidelity CFD simulations are conducted over a range of angles of attack, under both low- and high-speed flight conditions for the determination of the aerodynamic behavior of the UAV. The analysis focuses on extracting the key metrics related to pitch stability, including the speed at which pitch break appears, the deviation in pitching moment coefficient (ΔCm) at pitch break, and the corresponding angle of attack at which the phenomenon occurs. The results show that several configurations contribute to delaying the onset of pitch break and reducing ΔCm, indicating improved longitudinal stability. Notch-assisted dogtooth configurations further enhance these effects with minimal aerodynamic penalties. Overall, the study demonstrates that passive leading-edge modifications offer a viable and efficient solution for enhancing the low-speed aerodynamic behavior and control characteristics of BWB UAVs.