Brakes are one of the basic safety systems on a vehicle. During the operation of the vehicle, the brakes allow the vehicle to slow down, i.e., to adapt to traffic conditions or to stop, if necessary. However, in all conditions mentioned, emissions of brake wear products occur, which are very harmful to the environment because they can contain heavy metals. Working parameters of braking process are responsible for the intensity of brake wear, which can be tested in laboratory or road conditions, as well as by using modern software packages. This paper covers the basic theoretical assumptions about brake wear, as well as the materials applied in their production. The methodologies that other authors have come up with in their research are shown in this paper. Those methodologies are related to testing the brake wear, the parameters which are the most influential on wear, as well as the measures for the reduction of brake wear. The available scientific literature in the subject area lead us to the conclusion what should be taken into the consideration in future research and what factors are not thoroughly investigated, all with the aim of reducing the emission of brake wear.
4 February 2023 in Environmental Science and Pollution Research
The optimization of braking working parameters was conducted by analyzing the influential factors: vehicle speed (80, 100, and 120 km/h), a quarter of the vehicle mass (200, 250, and 300 kg), and brake pressure (3, 4, and 5 MPa). The goal was to achieve the lowest temperature on the braking pad contact surface and reduce braking time. Experimental work was conducted on the test rig BRAKE DYNO 2020. By applying ANOVA analysis, it was found that vehicle speed accounts for 72% of the influence on brake pad temperature, followed by vehicle mass and braking pressure accounting for 20% and 8%, respectively. On the other hand, for the mean value of simulated vehicle braking time, the brake pressure had the biggest influence (66.78%), followed by vehicle speed (21.75%), and a quarter of the vehicle mass (10.90%). Both the Taguchi method and the regression model showed a good correlation with the experimental results.
Correct determination of deceleration is very important from the aspect of the investigation of traffic accidents, because deceleration of the vehicle involved in the traffic accident is of key importance for the preparation of a quality finding and opinion of traffic expert. In this paper it was conducted the investigation how the change of the pressure affects the change ofthe temperature of the brake couple and how this change is later reflected in the deceleration of the vehicle and the braking distance. In order to find how the temperature influences the deceleration, it was conducted experimental investigation. The experimental investigation was conducted on the experimental test rig, which simulates the braking process for the quarter of the vehicle mass, and the experimental investigation was conducted for four different braking pressures: 2 MPa, 3 MPa, 4 MPa and 5 MPa. The temperature of the brake couple was measured during the entire braking process. Also the difference between Mean Fully Developed Deceleration and average vehicle deceleration is shown. It was found that for the case when the braking pressure was 5 MPa, the maximum deceleration value was greater than the value of gravity of Earth which may impair the stability of the vehicle. When the braking pressure was 2 MPa, 3 MPa and 4 MPa, the temperature increased respectively, but in the last measurement, when the braking pressure was 5 MPa, it began to decrease. Braking distance decreased with the increment of the braking pressure. Also, with the braking pressure increment, the deceleration increased in all cases.
14 September 2022 in Journal of Ambient Intelligence and Humanized Computing
During the transport, many factors can lead to the traffic accident. The highest number of accidents on the Republic of Serbia, where two vehicles participated are frontal collisions. In the paper are conducted two computational simulations of vehicles frontal collision, where in the first case, the vehicle one had speed of 90 km/h, and the second vehicle had the speed of 60 km/h, while in the second case, the speed of the vehicle 1 was 60 km/h, while the speed of the vehicle 2 was 90 km/h. both simulations were conducted in PC-Crash software package, which represent the special software for traffic accidents simulation. After the simulations, in the paper are presented the propositions and measurements for the reduction of the number of traffic accidents. On the basis of the conducted research, were drawn conclusions what should take into the consideration during the production of new vehicles.