Research efforts seek to develop aluminium alloy composites to enhance the poor tribological performance of aluminium alloy base matrix. In this research, a hybrid metal matrix composite (HMMC) was developed by reinforcing an aluminium alloy (AA8011) with SiC and rice husk ash (RHA) using a stir casting technique. RHA was prepared by the cracking of rice husk, which is abundantly available in the Indian subcontinent. The samples were cast by keeping the amount of RHA constant at 2.5 wt.% and varying the amount of SiC from 0.0 wt.% to 8 wt.%. The samples were machined to manufacture pins for wear tests (at ambient temperature, 100 °C, and 200 °C) and hardness measurement. The microstructures of the cast samples were analysed using an X-ray diffractometer (XRD) and a scanning electron microscope (SEM), along with energy-dispersive X-ray spectroscopy (EDS). It was observed that the composites with greater reinforcement of SiC exhibited improved hardness and wear resistance, but the coefficient of friction increased with the addition of RHA and SiC, and the wear performance deteriorated with an increase in the operating temperature. The contribution of RHA alone to the improvement in wear performance was marginal compared to the pure alloy. It was also confirmed that the reinforced composites could be a better option for automotive applications to replace aluminium alloys.
1 November 2019 in IOP Conference Series: Materials Science and Engineering
Currently, the world is facing scarcity of clean and potable drinking water. We have investigated whether the xylem (a porous conducting tissue) of a plant could be used as a filter to obtain drinking water. Firstly, we chose the appropriate plant for filtration based on our experimentation. Secondly, we used xylem to make a simple water filter and carried out experiments under the pressure head of the pump. Experiments were conducted using xylems of both angiosperms and gymnosperms. Freshly cut xylems of Ashoka tree, Silver Oak, Neem, Mango and Guava trees were screened for filtration. Filtration rate was measured for each plant and they were simultaneously checked for filterability of blue dye water solution. We found that sharp-edged, waxy leaf trees such as Ashoka and Silver Oak can filter water. These belong to the class of gymnosperms. Trees that bloom and give fruit (such as Neem) cannot purify water and remove impurities. The measured flow rate under a pressure of 2.5 psi was about 0.083 ml/s, which corresponds to a filtration rate of 7 litres per day or more and is sufficient for two people.
1 November 2019 in IOP Conference Series: Materials Science and Engineering
In this study, experimental research is carried out on two different class of refrigerants at three varied ambient conditions viz. (30°C, 35ºC and 40ºC) and three different air velocities viz. (1.25, 1.00, 0.75 m/s) in air cooled and evaporative cooled condenser. The first class is of low temperature refrigerant (R-134a) and the second is of high temperature refrigerant (R-410a). The results described that COP of high temperature refrigerant is greater than that of low temperature refrigerant. The COP increased with increasing air speed in air cooled and evaporative cooled condenser and decreased with increasing the ambient temperatures. For a fixed ambient temperature and air velocity, the COP of R-410a turned out to be greater than the COP of R-134a.Thus proving that high temperature refrigerant is better in performance than low temperature refrigerant.
Cracks in sinter component production are a significant concern in the field of powder metallurgy, and predicting and avoiding them is crucial for ensuring the quality and reliability of the final products. This study aims to contribute to this effort by investigating the variability of cracks under constant press settings by studying the performance of the compaction process. To this end, we intentionally induced cracks at different levels and studied the respective process performance. Our results show that with the same settings of the powder compaction press, 99% of the produced cracks could be found within a range of ±25% of the overall mean of the crack lengths. The lower and upper limits of crack lengths found and the approach presented for their determination can be used in future for the classification of good and bad parts on the basis of the availability of only a few crack measurements and permissible values of crack lengths that have yet to be defined.
29 September 2025 in International Journal of Structural Integrity
Purpose: Cracks in powder metallurgy (PM) components, being a common problem, pose significant manufacturing challenges but are detrimental to be detected as they affect the material’s mechanical properties. To detect these cracks, non-destructive testing (NDTs) methods are often used, but they come with high costs and time delays, as samples need to be extracted from production at given intervals. To overcome these limitations, an indirect method of crack detection, that is, modelling it as a binary classification, is explored in this work. Design/methodology/approach: This study introduces a supervised machine learning (ML) approach using force signal feature extraction to detect cracks. More specifically, a supervised learning algorithm is developed and validated for the classification of samples into samples with or without cracks based on the sensory data of the hydraulic press used for production. We compare different ensemble classifiers, including random forest (RF), AdaBoost (ADA), bagging, gradient boosting (GB) and extra trees (ET), in terms of their ability to classify workpieces using a dataset from real production. Findings: To this end, the present study deals with experimental workpieces of a specific type produced by manually adjusting the press parameters to artificially induce cracks in parts of the workpieces. The best-performing model resulted in a classification accuracy as high as 99% offering a cost-effective and efficient alternative to traditional NDT methods. Originality/value: This study provides a novel and indirect method for detecting cracks in PM components using ML models trained on press sensor data, which can significantly reduce the need for costly and time-consuming NDT techniques.