Li Zhang

Dr. Li Zhang

orcid

Research Focus & Metrics

Academic Career Length

4Years (2023-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
19 December 2023 in Crystals
Verified
Journal Article
Open access
PDF file
LZLi Zhang
Li Zhang
HZHui Zhao
Hui Zhao
LCLijia Chen
Lijia Chen
FLFeng Li
Feng Li
WZWeiqiang Zhang
Weiqiang Zhang
NGNingning Geng
Ningning Geng
The CoCrNi-based medium-entropy alloys (MEA) have been extensively investigated due to their exceptional mechanical properties at both room and cryogenic temperatures. To investigate the hot deformation behavior and the recrystallization mechanism of the CoCr0.4NiSi0.3 medium-entropy alloy, a series of deformation tests was conducted using the MMS-100 thermal simulation tester, with deformation conditions of 0.001–1 s−1/850–1150 °C. During the hot deformation process, the flow stress initially increases up to its peak value before gradually decreasing towards a steady state level. Higher flow stress levels are observed with increasing strain rate and decreasing deformation temperature. The estimated activation energy for hot deformation of this alloy is approximately 423.6602 kJ/mol. The Arrhenius-type constitutive equation is utilized to establish a modified model while incorporating power dissipation theory and the instability criterion of a dynamic material model to construct power dissipation maps and instability maps. By superimposing these maps, hot processing maps with strains of 0.4, 0.5, and 0.7 are derived. In this investigation, it is observed that regions of instability exclusively occur when the true strain exceeds 0.4. These regions of instability on the hot processing map align well with experimental findings. The suitable range of parameters for hot-working decreases as the true strain increases. The microstructure was analyzed using electron backscatter diffraction and transmission electron microscopy (TEM) techniques. The volume fraction of dynamic recrystallization (DRX) decreases with increasing strain rate but diminishes with rising temperature. The TEM characterization elucidated the mechanism of DRX in this MEA. The presence of the long-period stacking ordered (LPSO) phase was observed in both the face-centered cubic matrix and hexagonal close-packed recrystallized grains under different deformation conditions. The LPSO phase originates from the matrix at a low strain rate, whereas it is generated during recrystallization at a high strain rate. The observed increase in flow stress of the as-cast MEA is primarily attributed to the synergistic effects arising from the interaction of the dislocation with twins and the second phase. The onset of instability is effectively suppressed within a limited range through the formation of coherent second phases such as L12, LPSO, and superlattice structures resulting from phase transitions. These second phases serve as nucleation sites for recrystallization and contribute to the strengthening of dispersion. Furthermore, their interaction with dislocations and twins significantly influences both flow stress behavior and recrystallization kinetics under hot deformation. These findings not only deepen our understanding of the underlying deformation mechanisms governing MEA but also offer valuable insights for designing CoCrNi-based alloys with improved mechanical properties at elevated temperatures.

18 September 2023 in Crystals
Verified
Journal Article
Open access
PDF file
LZLi Zhang
Li Zhang
WZWeiqiang Zhang
Weiqiang Zhang
LCLijia Chen
Lijia Chen
FLFeng Li
Feng Li
HZHui Zhao
Hui Zhao
Ge ZhouGe Zhou
Ge Zhou
Focal research has been conducted on medium-entropy alloys (MEAs) that exhibit a balanced combination of strength and plasticity. In this study, the microstructure, dynamic mechanical properties, and texture evolution of an as-cast medium-entropy CoCr0.4NiSi0.3 alloy were investigated through dynamic compression tests at strain rates ranging from 2100 to 5100 s−1 using the Split Hopkinson Pressure Bar in order to elucidate the underlying dynamic deformation mechanism. The results revealed a significant strain rate effect with dynamic compressive yield strengths of 811 MPa at 2100 s−1, 849 MPa at 3000 s−1, 919 MPa at 3900 s−1, and 942 MPa at 5100 s−1. Grains were dynamically refined from 19.73 to 3.35 μm with increasing strain rates. The correlation between adiabatic temperature rise induced by dynamic compression and dynamic recrystallization was examined, revealing that the latter is not associated with adiabatic heating but rather with phase transition triggered by the dynamic stress during compression. The proportion of Σ3n (1 ≤ n ≤ 3) grain boundaries in deformation specimens increases with increasing strain rates during dynamic compression. The formation of specific three-node structures enhances both strength and plasticity by impeding crack propagation and resisting higher mechanical stress. In the as-cast state, significant anisotropy was observed in the MEA. As strain rates increased, it transited into a stable {111} F texture. The exceptional dynamic properties of strength and plasticity observed in the as-cast state of the MEA can be attributed to a deformation mechanism involving a transition from dislocation slip to the formation of intricate arrangements, accompanied by interactions encompassing deformation nanotwins, stacking faults, Lomer–Cottrell locks, stair-rods, and displacive phase transformations at elevated strain rates.

25 December 2024 in Journal of Materials Research and Technology
Verified
Journal Article
Open access
LZLi Zhang
Li Zhang
LCLijia Chen
Lijia Chen
WZWeiqiang Zhang
Weiqiang Zhang
HZHui Zhao
Hui Zhao
FLFeng Li
Feng Li

10 February 2025 in Crystals
Verified
Journal Article
Open access
PDF file
LZLi Zhang
Li Zhang
LZLingwei Zhang
Lingwei Zhang
XCXiang Chen
Xiang Chen
Materials utilized in extreme environments, such as those necessitating protection and impact resistance at cryogenic temperatures, must exhibit high strength, ductility, and structural stability. However, most alloys fail to maintain adequate toughness at cryogenic temperatures, thereby compromising their safety during cryogenic temperature service. This study investigates the quasi-static mechanical properties of a CoCr0.4NiSi0.3 medium-entropy alloy (MEA) at room temperature, −75 °C, and −150 °C. The deformation behavior and mechanisms responsible for strengthening and toughening at reduced cryogenic temperatures are analyzed, revealing that decreasing cryogenic temperature enhances the strength of the as-cast MEA. Specifically, both the yield strength (YS) and ultimate tensile strength (UTS) of the MEA increase significantly with decreasing temperature during cryogenic tensile testing. Under tensile testing at −150 °C, the YS reaches 617.5 MPa, the UTS is 1055.0 MPa, and the elongation to fracture remains approximately 21.0% at both −150 °C and −75 °C. After cryogenic temperature tensile deformation, the matrix exhibits a dispersed distribution of nanoscaled tetragonal and orthorhombic phases, a coherent hexagonal close-packed phase, L12 phase and layered long-period stacking ordered (LPSO) structures, which are rarely observed in the cryogenic deformation of metals and alloys. The metastable phase evolution path of this MEA at cryogenic temperatures is closely associated with the decomposition of perfect dislocations into a/6 Shockley partial dislocations and their subsequent evolution at reduced cryogenic temperatures. At −75 °C, the a/6 Shockley partial dislocation interacts with the L12 phase to form antiphase boundaries (APBs) approximately 3 nm thick. At −150 °C, two phase transition paths from stacking faults (SFs) to nanotwins and LPSO occur, leading to the formation of layered LPSO structures and deformation-induced nanotwins. The dispersion of these coherent nanophases and nanotwins induced by the reduced stacking fault energy under cryogenic temperatures is the key factor contributing to the excellent balance of strength and plasticity in the as-cast MEA, providing an important basis for research on the cryogenic mechanical properties of CoCrNi-based MEAs.