Hui Zhao

Dr. Hui Zhao


Research Focus & Metrics

Academic Career Length

4Years (2023-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 March 2023 in Journal of Physics: Conference Series
Verified
Conference Paper
Open access
PDF file
YZYu Zhang
Yu Zhang
HZHui Zhao
Hui Zhao
PLPengke Liu
Pengke Liu
MWMenghan Wei
Menghan Wei
YLYang Lu
Yang Lu
ZLZhanqi Liu
Zhanqi Liu
This paper investigated the effects of tempering temperature (200°C, 400°C, 600°C or 800°C) on microstructures, mechanical properties, and residual stress of 42CrMo4 steel. Microstructures were characterized by OM and SEM techniques. The results show that the change in tempering temperature leads to a change in austenite, resulting in a change in hardness and toughness. The specimen showed the best combination of mechanical properties under the heat treatment condition of a tempering temperature of 600°C. The hardness, yield strength, tensile strength, area shrinkage, and elongation reached 312.74HV, 759MPa, 898MPa, 60%, and 18%, respectively. The experimental results provide a reference for the selection of the heat treatment process of 42CrMo4 steel.

19 December 2023 in Crystals
Verified
Journal Article
Open access
PDF file
LZLi Zhang
Li Zhang
HZHui Zhao
Hui Zhao
LCLijia Chen
Lijia Chen
FLFeng Li
Feng Li
WZWeiqiang Zhang
Weiqiang Zhang
NGNingning Geng
Ningning Geng
The CoCrNi-based medium-entropy alloys (MEA) have been extensively investigated due to their exceptional mechanical properties at both room and cryogenic temperatures. To investigate the hot deformation behavior and the recrystallization mechanism of the CoCr0.4NiSi0.3 medium-entropy alloy, a series of deformation tests was conducted using the MMS-100 thermal simulation tester, with deformation conditions of 0.001–1 s−1/850–1150 °C. During the hot deformation process, the flow stress initially increases up to its peak value before gradually decreasing towards a steady state level. Higher flow stress levels are observed with increasing strain rate and decreasing deformation temperature. The estimated activation energy for hot deformation of this alloy is approximately 423.6602 kJ/mol. The Arrhenius-type constitutive equation is utilized to establish a modified model while incorporating power dissipation theory and the instability criterion of a dynamic material model to construct power dissipation maps and instability maps. By superimposing these maps, hot processing maps with strains of 0.4, 0.5, and 0.7 are derived. In this investigation, it is observed that regions of instability exclusively occur when the true strain exceeds 0.4. These regions of instability on the hot processing map align well with experimental findings. The suitable range of parameters for hot-working decreases as the true strain increases. The microstructure was analyzed using electron backscatter diffraction and transmission electron microscopy (TEM) techniques. The volume fraction of dynamic recrystallization (DRX) decreases with increasing strain rate but diminishes with rising temperature. The TEM characterization elucidated the mechanism of DRX in this MEA. The presence of the long-period stacking ordered (LPSO) phase was observed in both the face-centered cubic matrix and hexagonal close-packed recrystallized grains under different deformation conditions. The LPSO phase originates from the matrix at a low strain rate, whereas it is generated during recrystallization at a high strain rate. The observed increase in flow stress of the as-cast MEA is primarily attributed to the synergistic effects arising from the interaction of the dislocation with twins and the second phase. The onset of instability is effectively suppressed within a limited range through the formation of coherent second phases such as L12, LPSO, and superlattice structures resulting from phase transitions. These second phases serve as nucleation sites for recrystallization and contribute to the strengthening of dispersion. Furthermore, their interaction with dislocations and twins significantly influences both flow stress behavior and recrystallization kinetics under hot deformation. These findings not only deepen our understanding of the underlying deformation mechanisms governing MEA but also offer valuable insights for designing CoCrNi-based alloys with improved mechanical properties at elevated temperatures.

1 February 2026 in Journal of Physics: Conference Series
Verified
Conference Paper
Open access
JZJie Zhang
Jie Zhang
WDWenhao Deng
Wenhao Deng
HZHui Zhao
Hui Zhao
XYXiaohao Yi
Xiaohao Yi
In this study, the laser cladding technique was used to generate CoCrFeNiSi x (x = 0.4, 1.0, 1.6 at.%) high entropy alloy coatings with varying Si contents on the surface of Q235 low carbon steel. It was investigated how the Si content affected the laser cladding CoCrFeNiSi x alloy’s microstructure, microhardness, friction, and wear characteristics. The findings demonstrate that a good metallurgical link between the cladding layer and the substrate is consistently maintained as the Si concentration increases, and that the cladding layer’s surface is free of macroscopic fissures and other flaws. The hardness of the CoCrFeNiSi x high entropy alloy cladding layer rises from 172.8 HV to 315.7 HV as the Si content rises from 0.4 to 1.6. The cladding layer performs well overall against oxidation and abrasive wear. CoCrFeNiSi possesses the best wear resistance. The workpiece has the best overall wear resistance and loses 0.6 mg of mass before and after the friction and wear trial. In order to offer theoretical support for the composition design and practical application of laser cladding high-entropy alloy coating, this work examined the impact of Si content on the microstructure and characteristics of CoCrFeNiSi x high-entropy alloy coating.