Shengbao Wang

Prof. Shengbao Wang


Research Focus & Metrics

Academic Career Length

3Years (2024-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
26 August 2024 in Buildings
Verified
Journal Article
Open access
PDF file
JPjiangning pei
jiangning pei
XWXinzhi Wang
Xinzhi Wang
SQSonglin Qin
Songlin Qin
GXGuangpeng Xu
Guangpeng Xu
FSFulin Su
Fulin Su
ZLZHONGLONG LI
ZHONGLONG LI
Orthotropic steel bridge decks (OSDs) play a key role in long-span bridges, and full-penetration welding technology is crucial to improve their structural performance. This study proposes an innovative single-sided full-penetration welding rib-to-deck (RTD) joint technology. The accuracy of the numerical simulation in predicting the temperature field and stress field was verified by the combination of an experimental and numerical simulation, and the welding residual stress (WRS) of single-sided full-penetration welded RTD joints was analyzed. In addition, the effects of different welding parameters and RTD joint geometry on the WRS are discussed. The results show that the experimental results are consistent with the simulation results, indicating that the single-sided full-penetration welding technology without a groove is feasible. The WRS shows a peak tensile stress near the weld, which gradually decreases and transforms into compressive stress as the distance increases. In addition, the WRS of the roof surface and the U-rib surface increases slightly with the increase in the roof thickness and the welding speed. The research results are of great significance to optimize the welding process, improve the fatigue performance, and prolong the service life of steel bridge decks, providing a new technical method for bridge engineering.

26 September 2024 in Sensors
Verified
Journal Article
Open access
PDF file
JPjiangning pei
jiangning pei
SWShengbao Wang
Shengbao Wang
SQSonglin Qin
Songlin Qin
ZYZhijia Yu
Zhijia Yu
JGJianzhong Gao
Jianzhong Gao
ZLZHONGLONG LI
ZHONGLONG LI
An iterative correction method for the stress release coefficient, leveraging numerical simulation, has been innovatively developed to address the significant error issues associated with the blind-hole method in high-stress residual stress testing of steel structures. This method effectively reduces measurement error in high residual stress regions through a discriminant iteration process. The finite element analysis technology was employed to accurately simulate the blind-hole method’s test process, and additionally, Python was utilized for customizing the secondary development of ABAQUS software, thereby automating and optimizing the method. When compared with simulation and experimental data from the welding process, the efficiency, accuracy, and reliability of the correction method have been verified. The proposed method eliminates the need for tedious calibration experiments inherent in traditional methods, significantly enhancing the test’s automation level and convergence speed, and ensuring measurement accuracy, which provides an innovative solution for the accurate evaluation of residual stress in steel structures.

1 June 2025 in Materials
Verified
Journal Article
Open access
PDF file
Fei ZhuFei Zhu
Fei Zhu
YHYongcheng Hang
Yongcheng Hang
FWFenglai Wang
Fenglai Wang
SWShengbao Wang
Shengbao Wang
This paper presents a study on the uniaxial compressive behavior of fully grouted concrete bond beam block masonry prisms. A total of 45 (i.e., 9 hollow and 36 fully grouted) specimens were tested, and the failure modes and initial crack were reported. The effects of block strength, grout strength, and loading scheme on the compressive strength of the fully grouted prism were discussed. The results show that the compressive strength of bond beam block prisms increased with an increase in grouting, while they were less affected by the block strength; the peak strength of the grouted block masonry was, on average, 35.1% higher than the hollow masonry prism. In addition, although the specimens’ strength was lower under cyclic compression than under monotonic compression loading, the difference in their specified compressive strength was statistically insignificant. The stress–strain curve of block masonry under uniaxial compression was also obtained. Through nonlinear fitting, the compressive stress–strain relationship of grouted masonry, considering masonry strength parameters, was established, which demonstrated alignment with prior experimental studies. This study not only provides a strength calculation method for grouted masonry structures using high-strength blocks in the code for the design of masonry structures in China but also offers a dedicated stress–strain curve for precise finite element analysis and the design of masonry structures.

1 February 2026 in Journal of Physics: Conference Series
Verified
Conference Paper
Open access
FSFulin Su
Fulin Su
JGJianzhong Gao
Jianzhong Gao
YZYongjiang Zhang
Yongjiang Zhang
YYYang Ye
Yang Ye
SWShengbao Wang
Shengbao Wang
During the welding process, local heat input induces residual stress in the joint area, which significantly influences the service performance of the structure. Welding parameters, particularly the groove angle and welding speed, are critical determinants of the distribution of residual stress. In this study, a combination of finite element simulation and drilling method testing was employed to design 30 working conditions in order to analyze the coupled effect of these two factors. The results indicate that as the groove angle and welding speed increase, the longitudinal residual stress decreases markedly, thereby providing valuable guidance for process optimization.