Most species on Earth require access to sunlight for their physical and mental health. In ancient Greece and China, dwellings were oriented to take advantage of the sun.1 Even after much technological advancements, houses are still not constructed to save energy using the sun, even in view of climate changes. Aeschylus, a playwright of ancient Greece, would surely consider us to be barbarians based on our houses' orientations.1 New buildings incorporate more and more windows but too often with curtains or unaesthetic blinds. “Switchable glass,” also referred to as smart glass or smart windows, utilizes light-blocking elements directly embedded into or onto the glass. This technology could transform the way we interact with exterior and daylighting. Windows could be more energy-efficient than regular walls, by adjusting the solar heat gain when needed. Moreover advanced facades could provide better access to daylighting, a significant well-being improvement for workplaces and homes. Moreover, public health could benefit from these advancements; for example, the positive effect of daylighting through glass on microbial control inside of buildings was recently demonstrated.2
Polymethylmethacrylate (PMMA) is commonly applied to microfluidic devices due to its excellent biocompatibility, high optical transparency, and suitability for mass production. Recently, various surface treatment methods have been reported to improve the wettability of polymers, which is directly related to adhesion. In this research, the effect of a UV irradiation technique and an IPA rinsing technique as surface treatments for PMMA is investigated regarding the water contact angle of the PMMA surface. PMMA sheets that were 1.62 mm thick and commercially available were exposed to UV light with four different exposure times. Significant decreases in the water contact angle were observed after exposure to UV light, and the lowered contact angles due to the UV irradiation increased over time. According to the measurement, the water contact angle is a function of UV exposure dose as well as storage time after UV exposure. We examined the effect of a IPA rinsing process after UV irradiation and observed an increase in the water contact angle.
The application of Polyvinylidene Fluoride or Polyvinylidene Difluoride (PVDF) in harvesting energy from tire deformation was investigated in this study. An instrumented tire with different sizes of PVDF-based piezoelectric patches and a tri-axial accelerometer attached to its inner liner was used for this purpose and was tested under different conditions on asphalt and concrete surfaces. The results demonstrated that on both pavement types, the generated voltage was directly proportional to the size of the harvester patches, the longitudinal velocity, and the normal load. Additionally, the generated voltage was inversely proportional to the tire inflation pressure. Moreover, the range of generated voltages was slightly higher on asphalt compared to the same testing conditions on the concrete surface. Based on the results, it was concluded that in addition to the potential role of the PVDF-based piezoelectric film in harvesting energy from tire deformation, they demonstrate great potential to be used as self-powered sensors to estimate the tire-road contact parameters.
Recently, thermoplastic polymers have become popular materials for microfluidic chips due to their easy fabrication and low cost. A polymer based microfluidic device can be formed in various fabrication techniques such as laser machining, injection molding, and hot embossing. A new bonding process presented in this paper uses a 2.5% (w/w) polymethyl methacrylate (PMMA) solution as an adhesive layer to bond dissimilar polymers—PMMA to polycarbonate (PC)—to enclose the PMMA microfluidic channels with PC. This technique has been successfully demonstrated to bond PMMA microchip to PC film. This paper presents bonding strength using a shear strength test and a crack opening method in addition to the fluidic leakage inspection.
A vertically movable gate field effect transistor (VMGFET) is proposed and demonstrated for a micro-accelerometer application. The VMGFET using air gap as an insulator layer allows the gate to move on the substrate vertically by external forces. Finite element analysis is used to simulate mechanical behaviors of the designed structure. For the simulation, the ground acceleration spectrum of the 1952 Kern County Earthquake is employed to investigate the structural integrity of the sensor in vibration. Based on the simulation, a prototype VMGFET accelerometer is fabricated from silicon on insulator wafer. According to current–voltage characteristics of the prototype VMGFET, the threshold voltage is measured to be 2.32 V, which determines the effective charge density and the mutual transconductance of 1.545×10−8 C cm−2 and 6.59 mA V−1, respectively. The device sensitivity is 9.36–9.42 mV g−1 in the low frequency, and the first natural frequency is found to be 1230 Hz. The profile smoothness of the sensed signal is in 3 dB range up to 1 kHz.