Buildings subjected to elevated temperatures or thermal shock can be exposed to many changes in their properties, such as phase transformation and weight loss; therefore, the thermomechanical stability of mortars is essential to maintain their properties. In this work, different ratios of partially stabilised nano-zirconium oxide (ZrO 2 ) were used as a partial replacement by weight of kaolin to prepare a refractory mortar. Five ratios (5, 7.5, 10, 12.5, and 15%) of ZrO 2 , as well as unfired kaolin, water, and internal lubricant (potassium silicate) were applied to increase the specimen’s cohesion. The results showed that ZrO 2 additives are suitable to be used for the production of refractory mortar as a result of increased physical and mechanical strength.
1 January 2022 in Journal of the Mechanical Behavior of Materials
Generally, the major problems of moisture damage are caused by wetting, and particularly in construction, which has led to extensive research for the production of hydrophobic (anti-wetting) coatings. The aim of this research is to prepare an anti-wetting (hydrophobic) nanocomposite coating for different construction surfaces (ceramic, brick and gypsum). Hydrophobic nanocomposite coating was synthesized using electrospinning technique. Polymethyl methacrylate and polystyrene (PS) solutions were prepared in different ratios and then separately reinforced with ZrO 2 and ZnO nanoparticles. Contact angle, surface roughness, surface free energy and weathering effects were calculated for all specimens after being coated. All previously selected materials surfaces showed superhydrophobic and hydrophobic properties. The best results were obtained on ceramic surfaces after coating with PS/ZrO 2 . The water contact angle was 153° while the surface roughness was 0.491 µm and also showed the lowest surface free energy which was 5.5 mJ/m 2 . Weathering conditions tend to decrease the values of contact angle and this is due to the environmental effect of the weathering but they still have their hydrophobic properties. SEM test was used to determine the surface morphology and nanoparticle size for ceramic surfaces coated with PS and nano-ZrO 2 .
The properties of concrete are affected by various factors, some of which affect its strength and others affect its hardening. Curing methods are among the main factors that greatly affect the setting time and the speed at which it gains strength. In this study, heat curing was used to increase the speed of polymer concrete strength gaining. The mechanical behavior was investigated under two heating conditions (1 and 2 hours a day for a week) for unsaturated polyester polymer concrete specimens. Results showed that 87% and 90% of the compressive strength at 28 days are obtained after 4 days of 1 hr. and 2 hrs. of heat curing respectively, while 89% and 91% are obtained after 7 days of 1 hr. and 2 hrs. of heat curing respectively. In contrast, 86% and 93% of the splitting tensile strength at 28 days are obtained after 4 days of 1 hr. and 2 hrs. of heat curing respectively, also 90% and 94% are obtained after 7 days of 1 hr. and 2 hrs. of heat curing respectively
Reactive powder concrete (RPC) is a modern form of cementitious material. Major components include cement with a very low water-to-binder (w/b) ratio, steel fibres, superplasticizers, and very fine additives used in place of coarse aggregate, and very little water. The primary goal of this study is to examine the impact of immersion in sulfuric acid on compressive strength and to evaluate the impact of curing procedures on the preparation of RPC with high characteristics. The experimental work includes 4 mixes, which are prepared using 30 mm hooked-end steel fibers with a ratio of 0.4 by volume, silica fume and metakaolin with a ratio of 25% of cement weight. Compressive and indirect tensile strengths, ultrasonic velocity, and bulk density tests were conducted on the RPC that was prepared to evaluate its qualities. The results showed that heat curing resulted in a greater increase in strength than water curing did, and that mechanical properties improved with increasing SF more than MK additions. Heat-cured RPC demonstrated greater resistance to sulfuric acid immersion tests on compressive strength compared to water-cured RPC.
This study investigates the influence of heat curing on polymer concrete (PC) incorporating high replacement ratios (up to 80%) of recycled aggregates sourced from demolished buildings of different ages to prepare recycle aggregate polymer concrete (RAPC). The research addresses the gap in understanding how recycled aggregate properties, influenced by the age of source structures, impact PC performance under varying curing conditions. Two curing methods were applied: (1) air curing for 28 days and (2) accelerated heat curing at 100°C for 2 hours, followed by air curing. Results show that heat curing significantly enhances compressive strength, reaching 69 MPa in reference specimens compared to 53 MPa under air curing. When using 10-year-old recycled aggregates, RAPC maintained comparable strength (up to 65 MPa at 60% replacement), while 20-year-old recycled aggregates led to lower strengths (51 MPa at 60% replacement). The key contribution of this study lies in demonstrating that heat curing can compensate for strength loss in RAPC, enabling high replacement ratios while maintaining mechanical performance, knowing that the optimal balance between strength retention and sustainability was achieved at 60% replacement. Also, these findings underscore the potential of promoting sustainability by reducing natural resource consumption and construction waste.