Qiang Li

Prof. Dr. Qiang Li


Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
2 June 2022 in Materials
Verified
Journal Article
Open access
PDF file
QLQiang Li
Qiang Li
SCShikun Chen
Shikun Chen
YZYajun Zhang
Yajun Zhang
YHYunjin Hu
Yunjin Hu
QWQuanlin Wang
Quanlin Wang
Dongming YanDongming Yan
Dongming Yan
Geopolymer is a new type of synthesized aluminosilicate material. Compared with ordinary Portland cement, it has better fire resistance and durability, and is more environmentally friendly. In this paper, a high-strength metakaolin-based geopolymer composite (HMGC) has been developed by utilizing quartz powder and steel fibers. The optimization compositions and effect of curing temperatures (from ambient temperature to 90 °C) on the strength performance of the HMGC is studied. The optimized 1-day compressive strength of the HMGC can reach 80 MPa, and the 3-day compressive strength is close to 100 MPa (97.49 MPa). Combined with XRD, FTIR, SEM and MIP characterization, the mechanisms behind the strength development under different curing temperatures are analyzed. The results show that heat curing can significantly speed up the process of geopolymerization and increase the early strength of the HMGC. However, long-term heat curing under high temperature (such as 90 °C, 7 days) would reduce the mechanical strength of the HMGC. Prolonged high-temperature curing increases the pores and micro-defects in the gel phase of the HMGC, which may be attributed to chemical shrinkage. Thus, the curing temperature should be carefully controlled to make a HMGC with better performance.

15 September 2023 in Sustainability
Verified
Journal Article
Open access
PDF file
WFWeiwu Feng
Weiwu Feng
DYDa Yang
Da Yang
WDWenxue Du
Wenxue Du
QLQiang Li
Qiang Li
Structural health monitoring (SHM) and the operational condition assessment of blades are greatly important for the operation of wind turbines that are at a high risk of disease in service for more than 5 years. Since certain types of blade faults only occur during wind turbine operation, it is more significant to perform in situ SHM of rotating full-scale blades than existing SHM of small-scale blades or static testing of full-scale blades. Considering that these blades are usually not prefabricated with relevant sensors, this study performed SHM and condition assessment of full-scale blades in operation with stereo digital image correlation. A self-calibration method adapted to the outdoors with a large field of view was introduced based on the speckled patterns. To accurately obtain the in- and off-plane deformation, a new reference frame is constructed at the center of the rotation of the blades. The 3D displacements of the points of interest (POIs) on the blade of a 2 MW wind turbine were characterized. Furthermore, the frequency spectrum of the measured 3D displacements of the blades was compared with the blades with the faults. The results showed that the introduced technique is a convenient and nondestructive technique that enables SHM of full-scale wind turbine blades in operation.

19 April 2020 in International Journal of Civil Engineering
Verified
Journal Article
Closed access
PDF file
QLQiang Li
Qiang Li
LHLe Huang
Le Huang
HYHailong Ye
Hailong Ye
CFChuanqing Fu
Chuanqing Fu
XJXianyu Jin
Xianyu Jin

27 April 2021 in Materials
Verified
Journal Article
Open access
PDF file
Hui ChenHui Chen
Hui Chen
XZXiangqiang Zhou
Xiangqiang Zhou
QLQiang Li
Qiang Li
RHRui He
Rui He
XHXin Huang
Xin Huang
This study focuses on the dynamic compression performance of corroded steel fiber-reinforced concrete (SFRC) exposed to drying–wetting chloride cycles by a 37 mm diameter split Hopkinson pressure bar (SHPB) system. Three steel fiber contents (0.5%, 1.0%, 2.0%, by volume) were incorporated into concrete, and samples were subjected to drying–wetting cycles for different corrosion durations (30 days, 60 days, 90 days) after 28 days age. The sample damage mode, stress–strain curve and the dynamic compression performance of corroded SFRC were compared with plain concrete. Through the experimental data, strain-rate effect, fiber reinforcement effect and the corrosion duration influence on the impact compression property of SFRC were identified. The dynamic increase factor results of these samples were compared with the existing models in previous published literature. An empirical dynamic increase factor profile characterization model considering fiber content, corrosion duration and strain-rate is proposed.

15 March 2023 in Remote Sensing
Verified
Journal Article
Open access
PDF file
WFWeiwu Feng
Weiwu Feng
QLQiang Li
Qiang Li
WDWenxue Du
Wenxue Du
DZDongsheng Zhang
Dongsheng Zhang
The work performance of stereo digital image correlation (stereo-DIC) technologies, especially the operating accuracy and reliability in field applications, is not fully understood. In this study, the key technologies of the field remote 3D displacement sensing of civil structures based on stereo-DIC have been proposed. An image correlation algorithm is incorporated in improving the matching accuracy of control points. An adaptive stereo-DIC extrinsic parameter calibration method is developed by fusing epipolar-geometry-based and homography-based methods. Furthermore, a reliable reference frame that does not require artificial markers is established based on Euclidean transformation, which facilitates in-plane and out-of-plane displacement monitoring for civil structures. Moreover, a camera motion correction is introduced by considering background points according to the camera motion model. With an experiment, the feasibility and accuracy of the proposed system are validated. Moreover, the system is applied to sense the dynamic operating displacement of a 2 MW wind turbine’s blades. The results show the potential capability of the proposed stereo-DIC system in remote capturing the full-field 3D dynamic responses and health status of large-scale structures.

8 June 2021 in Materials
Verified
Journal Article
Open access
PDF file
RZRenzhan Zhou
Renzhan Zhou
QLQiang Li
Qiang Li
JWJiandong Wang
Jiandong Wang
KZKewen Zhou
Kewen Zhou
RHRui He
Rui He
CFChuanqing Fu
Chuanqing Fu
A newly proposed modified non-contact electrical resistivity measurement was used to test the resistivity of concrete and cement mortar. The oxygen diffusion coefficients of concrete and mortar were determined by a gas diffusion measurement, and the capillary porosity of concrete and cement mortar was measured by mercury intrusion porosimetry (MIP) measurement. The obtained electrical resistivity and capillary porosity results were verified with other researchers’ data, the measured electrical resistivity results can be estimated by a simple equation from the capillary porosity results. The obtained oxygen diffusion coefficient results were quantitatively correlated with capillary porosity and electrical resistivity measurement results. The proposed equations can be practically used to assess the electrical resistivity and oxygen diffusion coefficient.