Recently, there is an interesting discussion that has transpired around the world about the usage of plant extracts as corrosion inhibitors. We report that to control corrosion in mild steel (MS) specimens in a 1M HCl medium, Trochodendron aralioides (T. aralioides) extract was used as an economical green corrosion inhibitor. The various tests, namely, potentiodynamic polarization, weight loss measurements and electrochemical impedance spectroscopy (EIS) were performed to analyze the inhibition efficiency (IE) of the extract. The highest IE value of 96.42% was seen at 250 ppm, with the IE% increasing as the extract concentration increased. Potentiodynamic polarization suggests that T. aralioides plant extract acts as a mixed-type inhibitor. UV–visible (UV–Vis) and FT-IR spectroscopy were performed with the inhibitor to study the adsorption mechanism and surface analysis of the specimen, respectively. The results revealed that plant extracts form a protective film on the surface of the specimens, increasing inhibition and thereby reducing corrosion. Surface morphological studies such as AFM, EDX and SEM tests were performed in the presence and absence of the inhibitor with the results being analyzed by observing the surface of the metal.
Concrete is a versatile construction material used along with a reinforcement. Concrete is made up of binder materials and aggregates. Cement is a primary binder material used to produce conventional concrete. Carbon dioxide emissions in the atmosphere are a symptom of the issue related to Portland cement manufacture. It is estimated that one ton of cement produced releases an equal amount CO2 into atmosphere. On other hand, many industrial wastes are dumped in open spaces, leading to land pollution. Researchers have developed a construction material known as geopolymer concrete that uses industrial waste materials as a binder material to address these two issues. Excellent mechanical and durability characteristics are displayed by geopolymer concrete. For the creation of geopolymer concrete, fly ash is employed as a binder material. The drawback of utilizing fly ash is the curing method. Due to increased setting time, concrete samples require either heat curing or oven-curing. Geopolymer paste preparation is based on the type of binder materials used. In this study, GGBS is partially added with fly ash to cure specimens in ambient temperature due to presence of a higher amount calcium in GGBS. The present study investigates the consistency of geopolymer pastes, their workability, and the compressive strength of cement mortars by varying the amount of binder content (360 kg/m3 & 400 kg/m3). The molarity of NaOH was varied from 8 to 12. The ratio between binder material and alkaline to binder ratio were 0.45 and 0.50, respectively. The specimens were cured in both ambient and oven temperatures to study their strength development caused by temperature. A total of 396 specimens were cast to study the behavior of geopolymer concrete made with fly ash and GGBS (FAG). The test results revealed that the substitution of 50% GGBS with fly ash exhibited better strength properties during curing. Additionally, by increasing the binder content to 400 kg/m3, the results of 80% GGBS and 20% fly ash revealed excellent consistency among all other mixes. The oven-cured specimens showed more strength compared to specimens cured in ambient temperature, but the ambient cured specimens (ACS) attained the required strength. It was also not practically possible to cure the structural members by oven-curing in the field. The mix with 80% of GGBS and 20% fly ash can be used for construction. The required strength can also be achieved by increasing the molarity ratio.
Researchers have just discovered an alternative to synthetic corrosion inhibitors, which are hazardous and terrible for the ecosystem, to prevent rusting in the environment. A metal corrodes when it is subjected to corrosive media (acid, base, or saline) and they deteriorate, leading to failure. The most straightforward and affordable corrosion protection and prevention technique in acidic environments has been proven to be corrosion inhibitors. On industrial surfaces, pieces of machinery, or vessels, these inhibitors slow the rate of corrosion, preventing the monetary losses brought on by metallic corrosion. Recently, attention has been directed to developing ecologically appropriate corrosion retardation methods because inorganic and organic inhibitors are harmful and expensive. Recent studies have focused on green mild steel (MS) corrosion inhibitors that mimic industrial processes in acidic conditions. This presentation briefly covers the many types of corrosion, the corrosion process and the most recent studies on using natural plant extracts as corrosion inhibitors. Since they are safe and cost-effective, green corrosion inhibitors are a new trend in preventing corrosion. These inhibitors are produced from various plant parts, and inhibition efficiency (IE) also depends on them. To ascertain the IE of the corrosion inhibitor, some experiments, including computational studies (quantum calculations and MD simulations), electrochemical measurements (electrochemical impedance (EIS) and potentio-dynamic polarization), surface morphology atomic force microscopy (AFM), scanning electron microscopy (SEM)/energy-dispersive X-ray analysis (EDX) and UV–visible spectroscopy are carried out. It has been demonstrated that the IE is maximum for green corrosion inhibitors compared to synthetic inhibitors. This paper provides an overview of the properties, mechanism of corrosion inhibitors, nature of green corrosion inhibitors and their IE obtained by performing tests. This review article discussion shows that reinforcement with plant extract performs well in aggressive environments, which is evident from electrochemical studies and surface analysis when compared to reinforcement with inhibitors.