Propagation of a premixed flame from a closed to an open end in micro-channels with smooth non-slip isothermal walls is considered in the context of flame extinction dynamics. Powerful exponential flame acceleration in micro-channels with adiabatic walls has been demonstrated at the initial quasi-isobaric stage of the process [Bychkov et al., Phys. Rev. E 72, 046307 (2005)]. In contrast to the previous studies, here we investigate flame propagation in channels with isothermal walls. The problem is solved by means of high-fidelity laminar numerical simulations of the complete set of the Navier–Stokes combustion equations. For most of the problem parameter sets chosen, we obtain initial flame acceleration after ignition at the closed channel end. This acceleration resembles qualitatively the adiabatic case, but it develops noticeably slower, in an approximately linear regime instead of the exponential one and persists only for a limited time interval. Subsequently, heat loss to the walls reduces the temperature and hence the volume of the burnt gas behind the flame front, which produces a reverse flow in the direction of the closed channel end. When the amount of the burnt gas becomes sufficiently large, the reverse flow stops the acceleration process and drives the flame backwards with modifications of the flame front shape from convex to concave. Eventually, the flame extinguishes. Qualitatively, the process obtained reproduces a possible combustion failure during deflagration-to-detonation transition observed in previous experiments. We investigate the key characteristics of initial flame acceleration such as the acceleration rate and the maximum speed of the flame tip.
The melting of scrap and hot briquetted iron (HBI) in an AC electric arc furnace (EAF) is simulated by an advanced 3D computational fluid dynamics (CFD) model that captures the arc heating, the scrap/HBI melting process, and the solid collapse mechanisms. The CFD model is used to simulate a scenario where charge layering and EAF power profiles are provided by a real EAF operation. CFD simulation of the EAF operation shows proper prediction of the charge melting when compared with standard industry practice. Namely, the CFD model predicts a 32.5%/67.5% ratio of solid/liquid steel at the beginning of refining, which approaches the 30%/70% ratio used in standard practice. Based on this prediction, the melting rate in the CFD results differs by 8.3% from actual EAF operation. The impact of charge layering on melting is also investigated. CFD results show that distributing charge material into a greater number of layers in the first bucket (10 layers as compared to 4) enhances the melting rate by 12%. However, including dense material at the bottom of the furnace deteriorates melting performance, reducing the impact of the number of layers of the charge. The CFD platform can be used to optimize the use of HBI/scrap in real EAF operations and to determine best recipe practices.
Computational fluid dynamics (CFD)-based simulation has been the traditional way to model complex industrial systems and processes. One very large and complex industrial system that has benefited from CFD-based simulations is the steel blast furnace system. The problem with the CFD-based simulation approach is that it tends to be very slow for generating data. The CFD-only approach may not be fast enough for use in real-time decisionmaking. To address this issue, in this work, the authors propose the use of machine learning techniques to train and test models based on data generated via CFD simulation. Regression models based on neural networks are compared with tree-boosting models. In particular, several areas (tuyere, raceway, and shaft) of the blast furnace are modeled using these approaches. The results of the model training and testing are presented and discussed. The obtained metrics are, in general, very high. The results appear promising and may help to improve the efficiency of operator and process engineer decisionmaking when running a blast furnace.
During the refining stage of electric arc furnace (EAF) operation, molten steel is stirred to facilitate gas/steel/slag reactions and the removal of impurities, which determines the quality of the steel. The stirring process can be driven by the injection of oxygen, which is carried out by burners operating in lance mode. In this study, a computational fluid dynamics (CFD) platform is used to simulate the liquid steel flow dynamics in an industrial-scale scrap-based EAF. The CFD platform simulates the three-dimensional, transient, non-reacting flow of the liquid steel bath stirred by oxygen injection to analyze the mixing process. In particular, the CFD study simulates liquid steel flow in an industrial-scale EAF with three asymmetric coherent jets, which impacts the liquid steel mixing under different injection conditions. The liquid steel mixing is quantified by defining two variables: the mixing time and the standard deviation of the flow velocity. The results indicate that the mixing rate of the bath is determined by flow dynamics near the injection cavities and that the formation of very low-velocity regions or ‘dead zones’ at the center of the furnace and the balcony regions prevents flow mixing. This study includes a baseline case, where oxygen is injected at 1000 SCFM in all the burners. Two sets of cases are also included: The first set considers cases where oxygen is injected at a reduced and at an increased uniform flow rate, 750 and 1250 SCFM, respectively. The second set considers cases with non-uniform injection rates in each burner, which keep the same total flow rate of the baseline case, 3000 SCFM. Comparison between the two sets of simulations against the baseline case shows that by increasing the uniform flow rate from 1000 to 1250 SCFM, the mixing time is reduced by 10.9%. Moreover, all the non-uniform injection cases reduce the mixing time obtained in the baseline case. However, the reduction in mixing times in these cases is accompanied by an increase in the standard deviations of the flow field. Among the non-uniform injection cases, the largest reduction in mixing time compared to the baseline case is 10.2%, which is obtained when the largest flow rates are assigned to coherent jets located opposite each other across the furnace.
A tap‐to‐tap operation conducted in a 150 t AC electric arc furnace (EAF) by NLMK Indiana is used to validate a computational fluid dynamics (CFD)‐EAF solver. Model validation is conducted by comparing the electrodes position and melting rates obtained by CFD model against those reported in actual operation. Comparison demonstrates close alignment between simulation and actual process. Namely, electrode position is predicted with less than 5% error. Electrode bore‐in after the first bucket charge is predicted to within 3% of industrial data, whereas bore‐in prediction after the second bucket charge deteriorates due to arc instabilities driven by cave‐ins, not currently included in the CFD solver. At the beginning of the refining stage, the predicted ratio of solid to molten steel mass is 6% higher than that expected by industry. Validated tap‐to‐tap results are further analyzed to determine main features of the melting process. Specifically, in the results, reduction of molten steel temperature after each scrap charge and a temperature rise after electrode bore‐in are shown. Molten steel temperature further increases during the refining/melting stage due to reduction of arc heating losses. In the thermal analysis, it is shown that heating losses increase with pit size, reaching 25% right before charging of second bucket and 20% at the beginning of refining.
A continuous iron ore pellet feed system for a direct reduction ironmaking furnace is reportedly jamming in a hopper above the furnace, where a counterflowing gas seals off the furnace flue gas. The conditions that result in jamming are not well understood. The system is computationally modeled utilizing the coupled discrete element method (DEM) and computational fluid dynamics (CFD) technique. The technique is computationally expensive; therefore, the pellet sizing is modified while preserving the key metrics important in jamming. The model is used to study the impact of pellet moisture, heating, and ice formation between pellets in relation to the jamming event. The results indicate that the influence of moisture alone on the bulk shear rate is unlikely to jam the system and that insufficient heat is supplied by the counterflowing gas to raise the temperature of the pellets, which suggests freezing conditions can exist within the hopper. Particle bonding is implemented to replicate wet and icy pellets freezing and breaking up. The results indicate that the system jams in winter conditions when the hopper is charged with a minimum of 15% icy pellets, or 10% icy with 5% wet pellets. These results agree with industry reports of jamming during winter operations.