Context: Materials which exceed the balance of their production and destruction lead to the deterioration in the environment. Plastic is one such material which poses a big threat to the environment. A huge amount of plastic is produced and dumped into the environment which does not readily degrade naturally. In this paper, we address the organization of a large body of literature published on the management of waste plastics being the most challenging issue of the modern world.Objectives: To address the issue of the management of waste plastics, there is a dire need to organize the literature published in this field. This paper presents a systematic literature review on plastic waste, its fate and biodegradation in the environment. The objective is to make conclusions on possible practical techniques to lessen the effects of plastic waste on the environment.Method: A systematic literature review protocol was followed for conducting the present study [Kitchenham B, Brereton OP, Budgen D, Turner M, Bailey J, Linkman S. Systematic literature reviews in software engineering – A systematic literature review. Inf Softw Technol 2009;51(1):7–15.]. A predefined set of book sections, conference proceedings and high-quality journal publications during the years 1999 to September 2017 were used for data collection.Results: One hundred and fifty-three primary studies are selected, based on predefined exclusion, inclusion and quality criteria. These studies will help to identify the fate of different waste plastics, their impact and management and the disposal techniques frequently used. The study also identifies a number of significant techniques and measures for the conversion of waste plastic materials into useful products.Conclusion: Five fundamental strategies are used for the handling of plastic waste. These strategies include: recycling, depositing in landfill, incineration, microbial degradation and conversion into useful materials. All of these methods have their own limitations, due to which there is need to explore the studies for optimum solutions of the management of plastics waste.

Serious environmental deterioration caused by synthetic waste plastics, and the pollution of freshwater resources are the most alarming and marked challenges of the 21st century. Therefore, immense scientific efforts are being made towards the management of waste plastics and treatment of polluted water. The current study reports on the utilization of waste polyethylene terephthalate (wPET) and waste polystyrene (wPS) for fabrication of activated carbon (AC) and its application for the removal of hazardous polycyclic aromatic hydrocarbons (PAHs) pollutants from water. AC was prepared from wPET and wPS by carbonization under a N2 atmosphere followed by chemical activation with 1 M KOH and 1 M HCl. The AC was characterized by scanning electron microscopy, surface area analysis, and Fourier transform infrared spectroscopy. Adsorption of PAHs from aqueous solutions through AC was examined by batch adsorption tests. The optimum parameters for maximum adsorption of PAHs were found to be: initial PAHs concentration 40 ppm, 2 h contact time, pH 3, 5, and 7, 50 °C temperature and adsorbent dose of 0.8 g. Kinetic and isotherm models were applied to evaluate the adsorbent capacity for PAHs adsorption. The kinetic study shows that the adsorption of these PAHs onto AC follows pseudo-second-order kinetics. The experimental results demonstrated that the Langmuir isotherm model best fitted the data. The thermodynamic factors calculated such as entropy change (ΔS°), enthalpy change (ΔS°) and free energy change (ΔG°) show that the adsorption process is non-spontaneous and endothermic in nature. Results were also compared with the efficiencies of some commercial adsorbents used in practice. This examination revealed that the novel plastic-derived AC possesses a great potential for elimination and recovery of PAH elimination from industrial wastewater.

Lead (Pb) is a toxic environmental contaminant, which enters water bodies from natural and anthropogenic activities. The present study investigates the Pb concentration in groundwater sources and evaluates their potential health risks in Palosai area, Peshawar, Khyber Pakhtunkhwa, Pakistan. Groundwater samples were collected from different groundwater sources in the area where the human blood samples were from the dependent residents. Pb concentration was analyzed using an atomic absorption spectrophotometer and compared with the permissible limits set by Pakistan Environmental Protection Agency and World Health Organization (WHO). The levels of physicochemical parameters were observed within the said safe limits, while the levels of Pb in different groundwater sources (tube wells and wells) showed a little bit variation. Health risk indicators such as chronic daily intake (CDI) and hazard quotient (HQ) were calculated for Pb. The calculated value of CDI and HQ for Pb via groundwater consumption was 0.001 mg/kg·day and mg/kg·day, respectively; however, the overall HQ values of Pb in the groundwater were less than 1, indicating no health risk to the local depending community.

In the present study, water-soluble dyes like methylene blue (MB) and crystal violet (CV) were extracted from aqueous solutions utilizing biochar (EWB) produced from eucalyptus wood waste (EWW).

The negative impact of refinery wastewater is of great concern to the aquatic, terrestrial, and aerial environment. In this study, N-hexadecylchitosan (NHDC) was successfully synthesized to deal with low mechanical strength, poor adsorption capacity, and limited selectivity of native chitosan. The NHDC was characterized by fourier-transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM) and X-Ray diffraction analysis (XRD) to study its composition, morphology, and structural attributes. The adsorption of hydrocarbon pollutants from refinery wastewater was studied in batch mode experiments. The results indicated that the removal of COD attained by chitosan and NHDC was 21 and 63%, respectively. COD removal was found to be maximal, i.e., 96% using 0.08 g of NHDC at 60 min in a solution of pH 6.5 maintained at 60 °C. Furthermore, kinetic data revealed that the adsorption system followed pseudo-second order kinetics, whereas equilibrium studies supported both monolayer and multilayer adsorption mechanisms. The designed adsorption platform was able to capture hydrocarbon pollutants under very mild optimized conditions. Furthermore, NHDC demonstrated long term stability when subjected to five successive cycles, which contributed to the sustainability of water treatment systems. On the basis of the outcome of this work, it is advocated that new biobased NHDC can be used as an efficient adsorbent for the remediation of organic contaminants laden wastewater streams generated from oil refineries.

Sunset Yellow (SY) is a widely used synthetic azo dye in the food, pharmaceutical, and cosmetic industries, but its excessive release poses serious health and environmental risks. In this study, a magnetic molecularly imprinted polymer (MMIP)-based electrochemical sensor was developed for the selective detection of SY using 1-vinylpyridine as the functional monomer. Scanning electron microscopy (SEM) revealed irregular particle morphologies with an average diameter of approximately 69 nm, attributed to surface cavities formed during the imprinting process. Batch sorption experiments confirmed the high specificity of the MMIPs, with a maximum sorption capacity of 80 mg g ^− 1 under optimal conditions (pH 2, sorbent dosage 2 mg, contact time 18 min). Sorption kinetics followed a pseudo-second-order model, and adsorption behavior was best described by the Langmuir isotherm, indicating monolayer adsorption. Electrochemical measurements demonstrated that the fabricated sensor exhibited high sensitivity, selectivity, and stability for SY detection. The sensor performed optimally at pH 7, an accumulation time of 60 s, and a concentration of 1.5 × 10⁻³ M, with recovery values of 72.9–99.3% in real water and beverage samples, highlighting its practical applicability for environmental and food analysis. The LOD and LOQ values were found to be 5.82 × 10 ^− 5 M and 1.76 × 10 ^− 4 M, respectively. These results confirm the effectiveness of MMIP-based platforms for rapid, accurate, and selective monitoring of synthetic dyes in complex matrices.