Safeguarding drinking water is a major public health and environmental concern because it is essential to human life but may contain pollutants that can cause illness or harm the environment. Therefore, continuous research is necessary to improve water treatment methods and guarantee its quality. As part of this study, the effectiveness of coagulation–flocculation treatment using aluminum sulfate (Al₂(SO₄)₃) was evaluated on a very polluted site. Samplings were taken almost every day for a month from the polluted site, and the samples were characterized by several physicochemical properties, such as hydrogen potential (pH), electrical conductivity, turbidity, organic matter, ammonium (NH⁺₄), phosphate (PO₄³⁻), nitrate (NO₃⁻), nitrite (NO₂⁻), calcium (Ca²⁺), magnesium (Mg²⁺⁾, total hardness (TH), chloride (Cl⁻⁾, bicarbonate (HCO₃⁻), sulfate (SO₄²⁻), iron (Fe³⁺), manganese (Mn²⁺), aluminum (Al³⁺), potassium (K⁺), sodium (Na⁺), complete alkalimetric titration (TAC), and dry residue (DR). Then, these samples were treated with Al₂(SO₄)₃ using the jar test method, which is a common method to determine the optimal amount of coagulant to add to the water based on its physicochemical characteristics. A mathematical model had been previously created using the support vector machine method to predict the dose of coagulant according to the parameters of temperature, pH, TAC, conductivity, and turbidity. This Al₂(SO₄)₃ treatment step was repeated at the end of each month for a year, and a second characterization of the physicochemical parameters was carried out in order to compare them with those of the raw water. The results showed a very effective elimination of the various pollutions, with a very high rate, thus demonstrating the effectiveness of the Al₂(SO₄)₃. The physicochemical parameters measured after the treatment showed a significant reduction in the majority of the physicochemical parameters. These results demonstrated that the coagulation–flocculation treatment with Al₂(SO₄)₃ was very effective in eliminating the various pollutions present in the raw water. They also stress the importance of continued research in the field of water treatment to improve the quality of drinking water and protect public health and the environment.

This paper addressed the application of deacetylated xanthan (XGDS) and chitosan (CTS) as a mixture blend forming hydrophilic matrices for Tramadol (TD) sustained release tablets. XGDSs derivatives were obtained by alkaline treatment of xanthan gum (XG) with various degrees of deacetylation (DD). The obtained products were characterized in terms of structural, thermal and physicochemical properties. Different tablet formulations containing CTS/XGDSs were prepared by direct compression method and compared to CTS/XG tablets. Flow properties of powder mixtures and pharmaceutical characteristics were evaluated. The dissolution test of TD was realized under simulated gastric and intestinal conditions to achieve drug release more than 24 h. All developed tablets were found conforming to standard evaluation tests. It was shown that CTS/XGDSs matrices ensure a slower release of TD in comparison with CTS/XG based formulations. Meanwhile, increasing DD resulted in a decrease of drug release. In addition, TD release from XGDS matrices was faster at pH (6.8) than at acidic pH (1.2). The matrix tablets based on CTS/XGDS4 (DD = 98.08%) were selected as the best candidates compared to the other systems in prolonging drug release. The optimal formulation was found to release 99.99% of TD after 24 h following a non-Fickian type.

Environmental protection is becoming a primary objective when choosing processes and technologies for treating oily waters resulting from hydrocarbon production. The focus of treating oily waters is to eliminate contaminants from effluents before discharging them into the receiving environment while adhering to discharge standards. Our work aims to analyze the treatment process for oily waters in the API unit of the North Industrial Center (CINA), which involves a physical–chemical treatment using activated silica and Kurifix. The study aims to improve the treatment process used for oily water treatment to ensure water conservation for reuse. To enhance the CINA-HMD oily water treatment process, we created coagulants with different doses (C1–C6) using sodium silicate, activated silicate (sodium silicate + sulfuric acid), distilled water, Kurifix, and an oxygen scavenger while measuring pH, HC (hydrocarbon), and SS (suspended solids) levels. Coagulation and flocculation processes were used to remove suspended solids and hydrocarbons from the water. The results show that the coagulant used reduces suspended matter and hydrocarbon content and increases pH. The best treatment is achieved with a coagulant prepared with distilled water, 5% sodium silicate, and 2% sulfuric acid. The optimal dose of coagulant is 16 ppm. Automatic dosing provides better efficiency than manual dosing. The study recommends continuous verification of chemical preparation and injection, periodic cleaning of settling tanks, and monitoring of oily water entering the station.