In this study, we aim to minimize light loss and achieve high power conversion efficiencies (PCE) in perovskite solar cells (PSCs) by employing a spectral conversion film component with antireflection properties. In our scheme, NaYF₄:Tm, Yb, and Gd luminescent nanorod/silica nanosphere-based thin films are applied on CH₃NH₃PbI₃ PSCs to improve the device efficiency. The film was fabricated by spin coating an aged silica sol containing NaYF₄:Tm, Yb, and Gd luminescent nanorods. The size and the spectral conversion properties of the NaYF₄:Tm, Yb, and Gd luminescent nanorods were controlled by tuning the Gd³⁺ ion concentration. The microstructure and the transmittance properties of the thin film were controlled by changing the concentration of NaYF₄:Tm, Yb, and Gd luminescent nanorod in silica sol. The thin films have excellent spectral conversion properties while exhibiting a maximum transmittance. The photovoltaic performance of PSCs with NaYF₄:Tm, Yb, and Gd luminescent nanorod/silica nanosphere-based thin films was systematically investigated. The light transmittance was optimized to 95.1% on a cleaned glass substrate, which resulted in an average increase of about 3.0% across the broadband range of 400–800 nm. The optimized films widen the spectrum of light absorbed by conventional PSC cells and reduce reflections across a broad range, enhancing the photovoltaic performance of PSCs. As a result, the PCE of the PSC increased from 14.51% for the reference device without a thin film to 15.67% for the PSC device with an optimized thin film. This study presents a comprehensive solution to the problem of Fresnel reflection and spectral response mismatch of the PSCs, which provides new ideas for the light management of PSCs.

Bi₂Te₃-based alloys are representatively commercialized thermoelectric materials for refrigeration and power generation. Refrigeration mainly utilizes thermoelectric properties near room temperature, while the power generation temperature is relatively high. However, it is difficult for bismuth telluride to maintain good thermoelectric properties throughout the entire temperature range of 300–500 K. Herein, a series of Bi_xSb_2−xTe₃ alloys with different Bi contents were prepared by a simple preparation method and systematically investigated, and their best application temperature range was found. The Bi content can modulate carrier concentration and band gap, and the maximum dimensionless figure of merit (ZT) value of Bi_xSb_2−xTe₃ can be achieved in the corresponding application temperature range. The maximum ZT of Bi_0.3Sb_1.7Te₃ with a Bi content equal to 0.3 reaches 1.14 at 400 K, and the average ZT is 1.06 in the range of 300–500 K, which is suitable for both power generation and refrigeration. Therefore, power generation technologies with higher application temperatures should be selected from Bi_xSb_2−xTe₃ materials with Bi content less than 0.3, and refrigeration technologies with lower application temperatures should be selected with Bi content greater than 0.3. This work provides experimental guidance for finding the composition of Bi₂Te₃-based alloys in scientific research and practical applications.

This paper presents a design for a multi-level pattern generator based on Field Programmable Gate Array (FPGA) and Digital to Analog Converter (DAC). The proposed generator utilizes dynamic time error control to synthesize multi-level and pseudo-random bit sequence (PRBS) coding patterns, thereby expanding the application range of the pattern generator. To overcome the limited speed of FPGA logic resources and achieve a sample rate of 1.25 giga samples per second (GSPS) for the DAC, the design incorporates eight parallel channels of a processing unit. Experimental results demonstrate that the pattern generator can synthesize pattern signals at rates up to 120 mega samples per second (MBd) with voltage magnitudes of 2-level, 3-level, and 4-level.