This paper aims to provide a contribution to understanding the role of sludge macro-components (lipids, proteins and carbohydrates) on the yield/quality of bio-crude obtained via hydrothermal liquefaction (HTL). This was pursued by analysing the HTL process of real sludges and the mixtures thereof at different compositions, a topic that has been explored in a very limited way in the pertinent literature. The HTL experiments were run with municipal sludge, tannery sludge and a mixture of them in 25:75, 50:50 and 75:25 weight ratios in a batch reactor at 350 °C and for different residence times. The outcomes for a single sludge showed a greater bio-crude yield for the municipal one (42.5% at 10 min), which is linked to its significant carbohydrate content. The results obtained from the sludge mixtures suggested that a carbohydrate-to-protein mass ratio of 2:1 would maximise the bio-crude yield (average value of about 38%). Moreover, LC-MS and NMR analyses highlighted that the mixed sludges contributed to the formation of a higher number of compounds after the HTL treatment, with respect to the pure municipal or tannery sludge, with an increase in amine, alcohols and aromatic compounds.
This research work deals with the application of the calcium looping concept for thermochemical energy storage. Experiments were carried out in a lab-scale fluidised bed reactor, which was electrically heated. An Italian limestone (98.5% CaCO3, 420–590 μm) was present in the bed alone, or in combination with silica sand/silicon carbide (this last material was chosen as per its high absorption capacity in the solar spectrum). Calcium looping tests (20 calcination/carbonation cycles) were carried out under operating conditions resembling the “closed-loop” scheme (calcination at 950 °C, carbonation at 850 °C, fluidising atmosphere composed of pure CO2 in both cases). Carbonation degree, particle size distribution, and particle bulk density were measured as cycles progressed, together with the application of a model equation to relate carbonation degree to the number of cycles. Mutual relationships between the nature of the bed material and possible interactions, the degree of CaO carbonation, the generation of fragments, and changes in particle density and porosity are critically discussed. An investigation of the segregation behaviour of the bed material has been carried out through tests in a devoted fluidisation column, equipped with a needle-type capacitive probe (to measure solid concentration).
Concentrating solar power (CSP) technology with thermal energy storage (TES) could contribute to achieving a net zero emissions scenario by 2050. Calcium looping (CaL) is one of the potential TES processes for the future generation of CSP plants coupled with highly efficient power cycles. Research on CaL as a system for thermochemical energy storage (TCES) has focused on efficiency enhancement based on hybridization with other renewable technologies. This work proposes a novel solid management system to improve the efficiency of a CaL TCES system. The inclusion of a solid–solid separation unit after the carbonation step could lead to energy and size savings. The role of segregation between carbonated and calcined material on plant requirements is assessed, given the experimental evidence on the potential classification between more and less carbonated particles. The results show lower energy (up to 12%) and size (up to 76%) demands when the circulation of less carbonated material through the CaL TCES system diminishes. Moreover, under a classification effectiveness of 100%, the retrieval energy could increase by 32%, and the stored energy is enhanced by five times. The present work can be a proper tool to set the design and size of a CaL TCES system with a partial separation of the carbonated material.
Polymers are essential in modern life, but their large-scale production from non-renewable sources contributes to raw material depletion and environmental pollution. The shift from a linear to a circular economy aims to address these issues by promoting sustainable practices. Recent research focuses on incorporating natural fillers and biowastes to improve flame retardancy and reduce resource depletion. This work demonstrates the suitability of humic acids, biochar derived from both spent coffee grounds and the hydrothermal liquefaction of sludge, for use as flame-retardant additives in epoxy resins. The results are discussed in relation to the composition and preparation procedure of the composite materials. Particularly, the modification of epoxy chains with a proper coupling agent guarantees the uniform distribution of the waste throughout the polymer matrix.