Ramon Bargallo

Dr. Ramon Bargallo

orcid

Research Focus & Metrics

Academic Career Length

23Years (2004-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
23 November 2017 in IEEE Transactions on Energy Conversion
Verified
Journal Article
Open access
PAPedram Asef
Pedram Asef
RBRamon Bargallo
Ramon Bargallo
RBReza Barzegaran
Reza Barzegaran
ALAndrew Lapthorn
Andrew Lapthorn
DMDaniela Mewes
Daniela Mewes
This paper studies a dual-level response surface methodology (DRSM) coupled with Booth's algorithm using a simulated annealing (BA-SA) method as a multiobjective technique for parametric modeling and machine design optimization for the first time. The aim of the research is for power maximization and cost of manufacture minimization resulting in a highly optimized wind generator to improve small power generation performance. The DRSM is employed to determine the best set of design parameters for power maximization in a surface-mounted permanent magnet synchronous generator with an exterior-rotor topology. Additionally, the BA-SA method is investigated to minimize material cost while keeping the volume constant. DRSM by different design functions including mixed resolution robust design, full factorial design, central composite design, and box-behnken design are applied to optimize the power performance resulting in very small errors. An analysis of the variance via multilevel RSM plots is used to check the adequacy of fit in the design region and determines the parameter settings to manufacture a high-quality wind generator. The analytical and numerical calculations have been experimentally verified and have successfully validated the theoretical and multiobjective optimization design methods presented.

12 December 2018 in IEEE Transactions on Transportation Electrification
Verified
Journal Article
Closed access
PAPedram Asef
Pedram Asef
RBRamon Bargallo
Ramon Bargallo
ALAndrew Lapthorn
Andrew Lapthorn

4 March 2021 in Energies
Verified
Journal Article
Open access
PDF file
PAPedram Asef
Pedram Asef
RBRamon Bargallo
Ramon Bargallo
ALAndrew Lapthorn
Andrew Lapthorn
Davide TaverniniDavide Tavernini
Davide Tavernini
LSLingyun Shao
Lingyun Shao
Aldo SorniottiAldo Sorniotti
Aldo Sorniotti
This study investigates the influence of the buried magnet arrangement on the efficiency and drivability performance provided by an on-board interior permanent magnet synchronous machine for a four-wheel-drive electric car with two single-speed on-board powertrains. The relevant motor characteristics, including flux-linkage, inductance, electromagnetic torque, iron loss, total loss, and efficiency, are analyzed for a set of six permanent magnet configurations suitable for the specific machine, which is controlled through maximum-torque-per-ampere and maximum-torque-per-voltage strategies. Moreover, the impact of each magnet arrangement is analyzed in connection with the energy consumption along four driving cycles, as well as the longitudinal acceleration and gradeability performance of the considered vehicle. The simulation results identify the most promising rotor solutions, and show that: (i) the appropriate selection of the rotor configuration is especially important for the driving cycles with substantial high-speed sections; (ii) the magnet arrangement has a major impact on the maximum motor torque below the base speed, and thus on the longitudinal acceleration and gradeability performance; and (iii) the configurations that excel in energy efficiency are among the worst in terms of drivability, and vice versa, i.e., at the vehicle level, the rotor arrangement selection is a trade-off between energy efficiency and longitudinal vehicle dynamics.

21 June 2018 in IEEE Transactions on Sustainable Energy
Verified
Journal Article
Closed access
PAPedram Asef
Pedram Asef
RBRamon Bargallo
Ramon Bargallo
RBReza Barzegaran
Reza Barzegaran
ALAndrew Lapthorn
Andrew Lapthorn
This paper utilizes a Pareto-based, three-dimensional (3-D) analysis to identify complete and partial shading of photovoltaic (PV) systems for an complicated urban environment, where unusual shape of PV and installation topology is studied. The Pareto optimization attempts to minimize losses in a certain area with an improved output energy and without compromising the overall efficiency of the system of which, the nominal operating cell temperature (NOCT) for a glass/glass-module is considered as a significant parameter. The system is referenced to the environment based on IEC61215 via a closed-circuit and resistive load to ensure the module operates at the maximum power point. A Maximum Power Point Tracking (MPPT) controller is enhanced with an advanced perturb and observe (P&O) algorithm to maintain the PV operating point at its maximum output under various working conditions. The most cost-effective design of the PV module is achieved via optimizing installation parameters such as tilt angle, pitch, and shading to improve the energy yield. The parameter settings and suitability of the design are also determined based on the reduced amount of CO2 emissions. An experimental investigation has been carried out to verify the 3-D shading analysis and NOCT technique for both open-circuit and grid-connected PV modules.

5 December 2017 in Machines
Verified
Journal Article
Open access
PDF file
PAPedram Asef
Pedram Asef
RBRamon Bargallo
Ramon Bargallo
ALAndrew Lapthorn
Andrew Lapthorn
During field weakening operation time (FWOT), the total iron loss rises and affects the accuracy of loss prediction and efficiency, especially if a large range of FWOT exists due to a large voltage drop that was rooted from the resistance of the used material. Iron loss prediction is widely employed in investigations for a fast electrical machine analysis using 2D finite element analysis (FEA). This paper proposes harmonic loss analytically by a steady-state equivalent circuit with a novel procedure. Consideration of skin effects and iron saturation are utilized in order to examine the accuracy through the relative error distribution in the frequency domain of each model from 50 to 700 Hz. Additionally, this comparative study presents a torque-frequency-field density calculation over each single term of the modified institute of electrical machines formula (IEM-Formula). The proposed analytical calculation is performed using 2D FEA for a classic and modified IEM-Formula along with experimental verifications on a surface-mounted permanent magnet synchronous generator (PMSG) for a wind generation application.

25 February 2020 in Vehicles
Verified
Journal Article
Open access
PDF file
PAPedram Asef
Pedram Asef
RBRamon Bargallo
Ramon Bargallo
ALAndrew Lapthorn
Andrew Lapthorn
This paper presents study of a multi-slice subdomain model (MS-SDM) for persistent low-frequency sound, in a wheel hub-mounted permanent magnet synchronous motor (WHM-PMSM) with a fractional-slot non-overlapping concentrated winding for a light-duty, fully electric vehicle applications. While this type of winding provides numerous potential benefits, it has also the largest magnetomotive force (MMF) distortion factor, which leads to the electro-vibro-acoustics production, unless additional machine design considerations are carried out. To minimize the magnetic noise level radiated by the PMSM, a skewing technique is targeted with consideration of the natural frequencies under a variable-speed-range analysis. To ensure the impact of the minimization technique used, magnetic force harmonics, along with acoustic sonograms, is computed by MS-SDM and verified by 3D finite element analysis. On the basis of the studied models, we derived and experimentally verified the optimized model with 5 dBA reduction in A-weighted sound power level by due to the choice of skew angle. In addition, we investigated whether or not the skewing slice number can be of importance on the vibro-acoustic objectives in the studied WHM-PMSM.