It is of great interest and importance to resource utilization of waste biomass to produce porous carbon for environmental treatments. Pore structure and properties of the obtained carbon mainly relate to carbonization conditions and biomass types. In this work, a series of porous, biomass-activated carbons (AC) were prepared using shaddock peel, with ZnCl2 as a pore-forming agent. The effect of carbonization temperature and the mass ratio between ZnCl2 and shaddock peel were thoroughly investigated. The material composition, surface chemical properties, and surface structures of samples were carefully characterized. The specific surface area and adsorption capacity to methylene blue (MB) of adsorbents were changed with the carbonization temperature and the mass ratios between ZnCl2 and shaddock peel; when the temperature was at 1000 °C and the mass ratio was equal to 2:1, the resulting adsorbent had the largest specific surface area of 2398.74 m2/g and average pore size of 3.04 nm, which showed the highest adsorption capacity to MB to be 869.57 mg/g. The adsorption processes of biomass AC adsorbent matched the pseudo-second-order kinetic model and Langmuir isotherm model. This efficient and environmentally friendly biomass AC adsorbent from shaddock peel, activated by ZnCl2, is a promising candidate for the treatment of water pollution.
The continuous discharge of organic dyes into freshwater resources poses a long-term hazard to aquatic life. The advanced oxidation Fenton process is a combo of adsorption and degradation of pollutants to detoxify toxic effluents, such as anti-bacterial drugs, antibiotics, and organic dyes. In this work, an activated attapulgite clay-loaded iron-oxide (A-ATP@Fe3O4) was produced using a two-step reaction, in which attapulgite serves as an enrichment matrix and Fe3O4 functions as the active degrading component. The maximum adsorption capacity (qt) was determined by assessing the effect of temperature, pH H2O2, and adsorbent. The results showed that the A-ATP@Fe3O4 achieves the highest removal rate of 99.6% under optimum conditions: 40 °C, pH = 3, H2O2 25 mM, and 0.1 g dosage of the composite. The dye removal procedure achieved adsorption and degradation equilibrium in 120 and 30 min, respectively, by following the same processes as the advanced oxidation approach. Catalytic activity, kinetics, and specified surface characteristics suggest that A-ATP@Fe3O4 is one of the most promising candidates for advanced oxidation-enrooted removal of organic dyes.
It is of great importance to develop a spherical γ-alumina support with high hydrothermal stability to be used in platinum reforming catalyst processes. The porous pseudo-boehmite powder with a high surface area was first synthesized via a simple separate nucleation and aging steps method, and was then used as a precursor to produce a spherical γ-Al2O3 support via an oil–ammonia column method. The as-synthesized pseudo-boehmite has a substantially greater specific surface area of 336.0 m2·g−1 in comparison with the commercial Sasol boehmite powder (293.0 m2·g−1) from Sasol Chemicals. In addition, the as-prepared spherical γ-Al2O3 support derived from the as-synthesized pseudo-boehmite also possesses a higher specific surface area of 280.0 m2·g−1 compared to the corresponding Sasol sample. Moreover, the as-prepared spherical γ-Al2O3 balls demonstrate a much higher specific surface area of 185.0 m2·g−1 compared with the Sasol sample of 142.0 m2·g−1 after hydrothermal tests at 600 °C, suggesting its promising application in the chemical industry.
A series of porous silica materials coated with honeycomb-like magnesium silicate were prepared under hydrothermal conditions, using natural one-dimensional porous attapulgite as the template and a silicon source with different Mg/Si ratios, by adjusting the amount of MgCl2⋅6H2O and the attapulgite precursor and regulating pH. The influence of the Mg/Si ratios was carefully investigated on morphology, pore structure, and related adsorption actions toward methylene blue. The Langmuir isotherm and pseudo-second-order kinetic models were used to explain the adsorption behavior of methylene blue. The synthesized composite with the lowest magnesium content displayed the highest removal capability of 166.67 mg/g for methylene blue, with a zeta potential of −18.18 mV, a specific surface area of 310.4 m2/g, and an average pore size of 3.7 nm. The removal result was the synergetic adsorption between porous magnesium silicate grown on the surface and the rest of the silica, further indicating that the attapulgite is available as a silicon source and a rod-shaped template for magnesium silicate.