In this study, Cashew Nut Shell Liquid (CNSL)-epoxy matrix-based composites reinforced with borassus and tamarind fibres were fabricated using compression moulding technique. Three different types of composites were fabricated, namely Borassus fruit fine fibre/CNSL-epoxy composites (BF composites), Tamarind fibre/CNSL-epoxy composites (TF composites) and Tamarind/Borassus fruit fine fibre CNSL-epoxy hybrid composites (HB composites). In addition, CNSL-epoxy neat polymer was also fabricated for comparison. Physical properties such as micro-hardness, void percentage, and mechanical properties like tensile, flexural, Interlaminar Shear Strength (ILSS), and impact strength were investigated. Scanning Electron Microscope (SEM) was used to study the failure mechanism of the composites. Experimental results indicate that tensile and flexural properties of BF composites were higher when compared to TF and HB composites. Micro-hardness and impact strength of HB composites were better than the others. SEM images indicated better fibre-matrix bonding in BF composites indicating improved resistance to delamination. Thus, borassus and tamarind fibre reinforced CNSL-epoxy composites can be used as an alternative material for light to moderately loaded structural engineering applications.
Hybridization of synthetic and natural fibres as reinforcement makes the polymer composites environmental friendly and sustainable when compared to synthetic fibres based polymer composites. In this study chopped strand mat/pineapple leaf fibres were hybridized. Four laminates with six layers each, with different stack sequence (GGGGGG, GPPPPG, PGGGGP and PPPPPP) were fabricated using hand layup technique while maintaining a fibre to matrix ratio of 30:70 by weight with polyester resin as matrix. Mechanical properties such as tensile and flexural strength were determined and morphology of fractured specimens was studied. Maximum tensile strength of 180 MPa was obtained for the laminate with six layers of chopped strand mat followed by hybrid laminate with four layers of chopped strand mat at the centre (120 MPa). Tensile strength of hybrid laminate with four layers of pineapple leaf fibres at the centre was in third position at 86 MPa. Least tensile strength of 65 MPa was obtained for the laminate with six layers of pineapple leaf fibres. Similar trend was observed in case of flexural behaviour of the laminates with maximum flexural strength of 255 MPa and minimum flexural strength 107 MPa. Scanning electron microscopy of the fractured specimen reinforced with chopped strand mat only, indicated, fibre pull out, matrix cracking and lack of matrix adhesion to fibres. In case of hybrid composite (GPPPPG and PGGGGP) delamination was observed to be prominent due to improper wetting of the pineapple leaf fibres with the matrix. More significant delamination led to lesser strength in case of pineapple fibres reinforced composites even though the fibre pull out was relatively less.
Hard anodization is an electrochemical procedure used on aluminum and its alloys to enhance tribo‐corrosion performance by creating a thick oxide layer. Thermal residual stresses, resulting from the difference in the coating and substrate's thermal expansion coefficient, promote crack initiation and reduce the high‐cycle fatigue strength (HCF). This work hypothesizes that elastically prestraining the aluminum substrate can compensate for this mismatch, minimizing coating irregularities and improving fatigue strength without developing a new anodizing strategy for fatigue‐sensitive anodized components. Aluminum alloy 6082 is used as the substrate, and a device is built to apply tensile forces of 800 and 1000 N. Subsequently, the prestrained specimens are hard‐anodized with timeframes of 15 and 30 min, and the coating thickness, hardness, and morphology are determined. In addition, the HCF of the coated sample is analyzed and compared with the uncoated sample. Results reveal that prestraining influences the coating formation and characteristics, causing early crack initiation and fatigue failure. The observations show that tensile prestrain exacerbates coating deterioration rather than mitigating it, showing the complex interaction between the prestrain and thermal stresses in coating processes. This study demonstrates that prestraining combined with anodizing degrades the HCF performance of coated aluminum alloy.
The need to have biodegradable composites is aloft in today’s market as they are environment friendly and are also easy to fabricate. In this study, mangifera indica leaf stalk fibres were used as reinforcement along with saw dust as bio-filler material. Unsaturated isophthalic polyester resin was used as the matrix. The fibres were treated with 6 % vol. NaOH and neutralized with 3 % vol. of dilute HCl. Treatment of sawdust fillers was done by using 2% vol. NaOH solution. Hand layup method and compression moulding technique was used to fabricate the composite laminates. Specimens for evaluating the mechanical properties were prepared by using water jet machining. The results indicated an increase in tensile, flexural and impact strength of composites with addition of sawdust upto 3%. Further addition of the bio-filler resulted in decrease of mechanical properties.